Filter Results By:
Products
Applications
Manufacturers
UUT
assures a constituent's interoperability in a system.
See Also: Unit Under Test, DUT, System Under Test
- Pickering Interfaces Inc.
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
product
GENASYS High Density Matrix Switch Card, 104 X 8 X 8
GX6188 Series
The GX6188 is a 6U PXI, high density matrix, GENASYS architecture switching card. The card provides the user with the ability to connect and interface resources to multiple UUT connections. The board consists of two matrices - a 104x8 and a 8x8 matrix. The GX6188 can connect to 104 UUT switching points, eight external resources and an eight channel global bus via front panel connectors. Multiple GX6188 cards can be connected using the global bus. Like other GENASYS switch cards, the GX6188 features an integral, 3-dimensional switching architecture which provides the flexibility to connect test system resources to multiple UUT connections as well as supporting an expansion bus connection without sacrificing I/O matrix connections when building multiple switch card configurations.
-
product
PXI 32 Channel Switch Simulation Module
40-480-221
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
product
Test Program Execution for High-Volume Production Systems
ScanExpress Runner Gang
Electronic manufacturing test systems must be fast and efficient. Schedules today are shorter, products are more complex, and the market demands higher speed—the product needs to be built and shipped yesterday.ScanExpress Runner Gang Edition is a concurrent boundary-scan and in-system programming test executive designed specifically for high volume production. Unlike traditional test systems which execute sequentially on a single unit under test (UUT) at a time, ScanExpress Runner Gang Edition provides concurrent (gang) testing on up to 8 UUTs for improved test and programming times.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Chassis Controllers and Bus Expanders
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
product
ICT/FCT-Fixtures, Max UUT 250 × 180 mm (wxd)
CK-1 Small (Hold-Down Gate) / 230154
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
product
AIS Air Data Test System
F-16
The primary function of the Air Data Test System (ADTS) is to perform testing and fault isolation of pneumatic-type Units Under Test (UUTs). To test a UUT, the operator connects the associated Line Replaceable Unit (LRU) Integrated Test Adapter (ITA) to the rackmount Avionics Intermediate Shop (AIS) test station. The operator connects the ADTS to the IAIS via an RS-232 Interface and then finally, connects the UUT to the ADTS using the supplied cables and hoses.
-
product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781421-12
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Solar ATE
MS 1534
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
product
Combination Board Tester
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Power Interface and Prototype PXI Card
GX7404
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
product
Digital and Analog Test Sets
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
product
MTA Wiring Analyzer
2650
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
ITA, G12, Front Mount, 12 Module With Protective Cover
410104322
The G12 ITA can be used with all G12 Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Test & Measurement Services
We specialize in the development of advanced automatic test applications based on NI TestStand.- Development of NI Test Stand test programs, with code modules in LabVIEW, LabWindows/CVI, Measurement Studio/.NET, C/C++, and ActiveX/COM- Integration of test and measurement instrumentation, switching, and UUT bus interfaces- Customization of step types, process models, operator interfaces, reports, and databases- Integration in the enterprise software infrastructure (XML data formats, databases, web applications, etc.)- Integration of the NI TestStand ATML Toolkit
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 6 GHz, 50 Ω, SMA, Failsafe
42-784B-101
The single slot remote multiplexer versions occupy less PXI panel space and allow the microwave relays to be placed closer to the UUT and other RF test equipment. In some applications it can shorten the length of RF cable runs and improve system performance. The remote multiplexers are supplied complete with a 1.5 m interface cable.
-
product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
