Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire 1 Port MateNet, 1 Position
7-142716763-036
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire 1 Port MateNet, 1 Position.
-
product
Cable Testers
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
product
Lan CAble Testers
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
product
Cable Management Tools and Testers
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
product
Function Tester with Low Number of Channels
UTP 6010 RF
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
product
Quintest
4400600
Tests UTP, STP & Installed Networks Tests & Verifies Short circuits, open circuits, pair reversals & miswires 2, 3 & 4 pair voice data channels Instant results via LED display Automatically tests for Screen Auto power off Low Battery Indicator
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
-
product
8K ip Camera Tester M-IPC-450C with TVI 5.0 Audio, Wrist Design
M-IPC-450C
Fuzhou Metricu Technology Co Ltd
8K wrist tester M-IPC-450C supports 8K ip camera, analog camera, 8MP TVI camera, 8MP CVI camera and 8MP AHD camera. (5 in one)It also supports DC12V 3A, 48V PoE 25.5W power output, UTP cable, RJ45 TDR cable, RS485, Audio in, TVI 5.0 audio, wrist design, etc.
-
product
UTP Cable Tester
21-8574-00
The Lan Cable Tester is consists of unshield RJ45:568A, 568B & USOC. The tester also easy to operate, the user begins testing by connecting. The multiple LEDs showed indication. This Lan Cable Tester is very practical tester can be easily read and correct pin configuration of cable continuity, open, short, miswiring, & no connection.
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
Power over Ethernet
PoE Tester
Covering both commercial and industrial applications, PLANET Power over Ethernet (PoE) products offer highly-dependable power and data transmission. Featuring 802.3bt standards, intuitive touch LCD design, Long Reach PoE technology over fiber optic cabling, coaxial cabling or UTP cabling, and PLANET exclusive intelligent PoE Management functions, all the requirements can be met for such applications as IP surveillance, IP communications, POS systems, PoE lighting and more. Our full range of PoE product lines include 95W 802.3bt PoE++/ 30W 802.3at PoE+ Managed Switches, Industrial flat-type PoE+ Switches, PoE Injectors, Splitters, Extenders designed for both indoor and outdoor environments.
-
product
Car Camera Bus (C2B)
Analog Devices Car Camera Bus (C2B™) is an innovative new camera link technology enabling HD video over Unshielded Twisted Pair (UTP) cables and unshielded connectors. C2B provides an easy upgrade path from SD to HD cameras without the need to change the existing cable and connector infrastructure. C2B enables a camera link with reduced system cost, significant weight savings and increased robustness. The C2B portfolio of transmitter and receiver devices enable seamless camera connectivity in the vehicle. The C2B technology was defined and designed for automotive applications and provides a robust camera link solution for these applications:
-
product
Scalable Tester System for Functional Testing
UTP6010
The UTP6010 is a scalable tester system for functional testing, comprising an integrated main switching unit, a keyboard drawer and a swivelling monitor. It is the reliable, modular, low priced UTP starter kit. The system is suitable for tester applications, where space-saving devices are required, because its construction height is only 12 HU (excluding keyboard drawer and main switching unit).
-
product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
product
Automotive Ethernet Interface Device
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
CATx Surge Protector
SP-CAT5-6V
Protects sensors running on CATx unshielded twisted pair (UTP) cable against the effects of electrostatic discharge, faulty wiring and lightning. The use of two protectors on each end of the line will provide increased protection for each end against surges. Protected pins: (1,2) (3,6) (4,7) and (7,8) pass through. Impedance: 85 to 115 Ohms. Surge suppression: 22Vpeak @ 100A 10/1000µs. Maximum continuous voltage: 6Vpeak. Dimensions WxDxH: 1x3.6x0.9 in (25x91x23 mm). Regulatory approvals: GR 1089, NEC 800.100 and 830.100, ITU 703, UL94 V0 Flame Rated.
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
product
Hand-held Cable Tester
STM-8
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
UTP Software Suite
Increasing customer requirements, shorter product cycles and higher time to market demands dramatically influence the long-term goals in software development. With the Universal Test Platform Software Suite (UTP Suite), we introduce a robust standard that features a great set of tools for configuring, developing, analyzing, debugging and executing test sequences.
-
product
Quadruple Function Tester with Shielded HF Test Chambers
UTP 9011 RF
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
product
Double Function Tester with Shielded HF Test Chambers
End-of-line Tester UTP 9010 RF
The UTP Series 9010 is a scalable test series available in a variety of feature-rich variants and many designs. The UTP 9010 RF function tester shown here as an example is suitable for tests with a medium number of channels and complexity. It is designed for parallel testing of two or more test items. The measuring instruments used are used alternately for several test items. Due to its compact design and construction as a modular system, this powerful tester can easily be expanded to larger numbers of channels.The integrated HF test chamber UTP 5070 developed by NOFFZ allows an independent shielded test. It can be operated manually or fully automatically by a robot .The basic version of the UTP 9010 series is an ideal system for functional and end-of-line tests and is already preconfigured for this purpose. The RF tester presented in the example is used in particular to test infotainment and eCall modules in the vehicle as well as IoT products with wireless technologies.
-
product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
product
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot
7-142716765-072
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot.Note: Static Bend Radius - 19.2mm [.76in], Flex Bend Radius - 48mm [1.89in]
-
product
Media Conversion
PLANET provides a comprehensive Media Conversion solution from the Edge to the Core to extend communication distance of the Ethernet network via fiber optic cabling, existing coaxial cabling or UTP cabling. We provide our customers with stable and efficient media conversion with a wide range of media converters that meet the demands of various environments such as Telecom, Enterprises, Data Center, Factory and FTTx. Our state-of-the-art media converters featuring high durability and versatility are ready to perform in any kind of business and industrial environment with excellent transmission quality over long distance and fast speed!
-
product
Glass Break Detection Sensor
ENVIROMUX-GBS
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
product
Universal Tester Platform
In order to meet these growing demands towards tester system NOFFZ has developed the Universal Tester Platform – UTP. The UTP 9010 series is the first scalable member of this innovative product family.
