Filter Results By:
Products
Applications
Manufacturers
Solar
energy of the sun's rays.
-
product
Semi-auto 4 Point Probe System for Solar Cell Substrate
RG-100PV
*Measurement system for thin film on substrate samples for multi-points measurement*Even pitch and random pitch for Max.1,000 points*2-D/3-D square mapping software for even pitch
-
product
On-site EL/PL Inspection Machine
“EPTiF”
"EPTiF (EL/PL Test in Field)" enables you to check invisible conditions of installed solar panels during daytime by EL and PL inspections, which are adopted by a number of solar panel manufacturers, without detaching solar panels. Irradiance-independent and steady results can be obtained. This is the first in the industry.
-
product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
Identifies defect position instantly- contributes to saving inspection time
-
product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
product
Solar Power Meter
SOLAR POWER METER* 3 functions : Solar power, Power integration, Transmission* Select either W/m^2 or Btu / (ft^2xh) power units. Real time SD memory card Datalogger, it Built-in Clock and Calendar, real time data recorder.sampling time set from 1 second to 3600 seconds.Spectral 400 to 1100 nm2000 W/m^2, 634 Btu/( ft^2 x h )
-
product
TriSOL Large Area Solar Simulators
OAI has designed and engineered for large area markets Class AAA, ABA, or ACA Solar simulators with the same performance , quality, and reliability as our other solar simulator models. These large area solar simulators are available in several models.
-
product
Solar Cell I-V Characterization System
VS6821
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
-
product
Environmental Testers
When you’ve got a specialized job to do, general-purpose tools won’t do. Whether you’re measuring sound, light, water or solar energy, depend on Amprobe for affordable, environmental test solutions.
-
product
Solar PV Testing
We've been manufacturing solar PV testing solutions for nearly a decade and have become a trusted name within the industry. Whether you are a residential, commercial or utility scale PV installer, or testing 1000V and 1500V installations, we have a PV testing solution for you.
-
product
Engineered Systems
AMETEK Programmable Power, Inc.
When a catalog product cannot completely satisfy a requirement, AMETEK Programmable Power's Solutions Business provides custom power supply systems and integrations. The solutions range from OEM integration for medical and semiconductor industries to modular avionics ATE power subsystems to turnkey solar array simulators for satellites. We also can modify power supplies to meet your application requirements.
-
product
Portable Solar Simulator
XES-40S3
We have manufactured the highly accurate solar simulators, which is used for evaluations where sunlight needs to be recreated. By fully utilizing these technologies, we have developed this portable Solar Simulator, which can easily reproduces sunlight. Our device is optimum solution for initial evaluations and inspections for the research purpose.
-
product
Multiple Output Bidirectional PSU
LAB-MOBI
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
product
Ventilation and Heating Unit
HD9906.51
The heating and ventilation unit is meant to be used with solar radiation sensors (pyranometer, pyrgeometer and radiometer) and can be used outdoor under any weather conditions.
-
product
Solar Simulator
Sun 3000 Class AAA
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. Photofeedback and digital shutter timer are included.Standard maintenance, lamp or filter replacement, does not require any tools. Locking indicator dials on all the system controls provide for a reproducible and stable setup. A built-in beam imaging accessory assists in system alignment.
-
-
product
High Intensity Pulsed Solar Simulator
GEN 2
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
product
Solar Simulator
Unisim Compact Solar Simulator
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
product
Solar Cell Simulation
Setfos
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
product
Bidirectional Power Supply Device with Regeneration Capability
KP Series
KP series is the sophisticated bidirectional power supply device with the regeneration capability*, optimal for evaluating not only in-car inverters for hybrid and electric vehicles but motors, generators, high-capacity vehicle batteries and capacitors as well as wind or solar power generation. We make available the extensive lineup ranging from 2kW to 120kW so you can choose the optimal model according to various applications including development and production.
-
product
DC Power Supply
62000H
Chroma Systems Solutions, Inc.
Chroma’s new 62000H Series of programmable DC Power Supplies offer many unique advantages for telecom, automated test system & integration, industrial, battery charge & simulation for hybrid cars and solar panel simulation. These advantages include a high power density of 15KW in 3U, precision readback of output current and voltage, output trigger signals, as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations. For high power applications, parallel up to 10 units for up to 150kW.
-
product
Water & Weather Node
SmartGuard
The next generation sensor and instrument HUB for Ocean, Lake, Reservoir, Estuary and River Hydrometric stations.Monitoring water and weather conditions is essential in many operations and the SmartGuard node is well suited for stand-alone stations powered by battery and solar power utilizing wireless real-time data communication.Designed for ease of integration of new and existing sensor technologies into a single Aanderaa observatory node with modern self-describing XML data output formats.SmartGuard interfaces with all Aanderaa atmospheric and in water sensors, along with most 3rd party sensors.
-
product
Measurement Solutions
Accurate performance measurement is vital in module production. Final quality control with an IV tester is the last step in the production process before a solar module leaves the factory. halm offers module testers that are able to measure all available module technologies and cater to various factory layout requirements.
-
product
Data Logger for Weather Station, 4G
HD33MT.4
HD33MT.4 with 4G/3G/2G/GPRS modem. Optional Ethernet. Designed for solar power. Integrated charger. Data Logger for weather station - remotely monitoring temperature, humidity, atmospheric pressure, solar radiation, rainfall quantity, wind speed and direction. Calculating sunshine duration.
-
product
Complex Environment Simulator
Complies with IEC60904-9 solar simulator/classes B and C. Includes integrated temperature and humidity controls, allowing the output measurement testing and the complex durability testing to be conducted by one unit. The work size and the temperature/humidity control range, etc. can be customized.These chambers are available at Iwasaki for testing your samples; please contact your local agent for details.
-
product
Precision Energy Meter
WattsOn – Mark II
Ideal for Energy Management, Solar, Export Limit, Building Automation and OEM Applications. The WattsOn-Mark II Precision Energy Meter uses cutting-edge metering technology to provide unprecedented accuracy, resolution and metering performance for any electrical installation. WattsOn monitors each phase individually and incorporates the functions of single-phase, split-phase, and three-phase meters.
-
product
Solar Simulators
Sun 2000 Class A
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house -no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
product
Solar Simulator
Unisim
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
product
Reference Cells
Reference cell is used for measuring and setting the intensity of solar simulators for one sun (or other user desired) intensity condition. They are also used to calibrate the IV Measurement system photo-detector intensity to match the measured ISC to calibrated ISC.
-
product
Solar Array Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
