Filter Results By:
Products
Applications
Manufacturers
Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
- Pickering Interfaces Inc.
product
PXI Precision Resistor Module 18-Channel, 1 to 62.1
40-297-011
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Virtual Platform Development and Simulation
DEV
The Imperas Developer products consist of tools, models and infrastructure components critical for the high quality, rapid development and verification of embedded software, utilizing virtual platforms. The Developer products provide the necessary capabilities to develop platforms, including software simulation capability to execute embedded code on the platforms.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI
PCI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - PCI & PCIx Compatible, 3.3V and 5V OperationApplication interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
product
Portable Calibrator
MC141
Voltage range from 0 to 750 V DC/AC with uncertainty 0.01% Current range from 0 to 2 A DC/AC with uncertainty 0.02 % Calibrated sinusoidal output signal DC - 1kHz. Set standard resistors from 10 Ohm to 100 MOhm in decade values with uncertainty 0.02 %. TC temperature sensor simulation R, S, B, J, T, E, K, N in range from -250 oC to 1850 oC
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 925Ω
50-298-121
The 50-298-121 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
2-Axis Rate and Position Tables
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
PHIL 4-Quadrant Power Amplifier
PAV5000
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
product
PXI Precision Resistor Module 6-Channel, 3 to 1.51M
40-297-050
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-011
The 40-297A-011 (PXI) and the 42-297A-011 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 61 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Universal Breakout Test Fixture
CA-323
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
Pattern Conversion
Wave Wizard
Wave Wizard generates a test program according to device spec. It avoids the inherent problems that exist when trying to force an event-driven simulation into a constrained ATE test program, by considering device perspective.
-
product
Multi-Protocol Board
EXC-8000cPCI
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-130
The 40-297A-130 (PXI) and the 42-297A-130 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 6.97 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Network Testing Tools
Network IP traffic packet generators are used for network performance testing under maximum or partial throughput conditions. Network health can be analyzed by network traffic measurement in a testbed network, using an IP network traffic generator such as IP Traffic Test and Measure. The traffic generator sends packets, often with a unique packet identifier, making it possible to keep track of the packet delivery in the network.Network impairment simulation (emulation) is a technique for testing the performance of real applications over a virtual network. The aim is to assess performance, predict the impact of change, analyze impairment conditions or otherwise optimize technology decision-making. Measurements usually focus on simulation of conditions like delay, jitter, latency, dropped packets and limited bandwidth.
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Range-Doppler Target Generators
ATG9100
The ATG-9100 is an example of a laboratory-quality instrument that will simulate complex target motion. Microwave signals from the speed camera enter the instrument through an integrated antenna which is then downconverted and digitized. Target simulation data is added to the digitized signal to provide range and Doppler information. The modified digital data is then converted back to an IF and upconverted to the original microwave frequency of the speed camera and radiated back through the antenna. Since the ATG-9100 can be phase-locked to an external 10 MHz reference standard, this instrument is suitable for use as a calibration standard for speed cameras.
-
product
MIL-STD-1553 Test & Simulation Instrument for PXI
PXI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Time Synchronization to PXI 10MHz reference clock - Real-Time recording and physical bus replay - PXI trigger generation on 1553 bus events - Initiate BC, RT Simulation and BM Capture on PXI Triggers - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PXI 32 Channel Switch Simulation Module
40-480-221
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
product
HTOL RF Testing Systems
Becker Nachrichtentechnik GmbH
Fully Automatic Test Systems for Lifetime Simulations of Electronic Components. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage. A graphical user interface enables an intuitive and easy control.
-
product
Simulating Optical Design Components
Wave Optics Module
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-153
The 40-297A-153 (PXI) and the 42-297A-153 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Battery Cell Simulation / Emulation
BMS
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
product
PXI & LXI Simulation Tools
Our PXI & LXI simulation tools help you to accelerate the development process by simulating the product in your test system. These tools allow you to develop and test the system software independent from your application hardware. By using the tools, you can minimize the time required with the physical system.
-
product
BOSS Simulator
Softdel’s BOSS Simulator is a sophisticated BACnet monitoring, debugging and simulation program that runs on any Windows® computer. It has a simple interface that is easy to use for BACnet professionals as well as novices. BOSS Simulator extends the functionality of Softdel’s BOSS Explorer by adding complex simulation and troubleshooting features, including support for A-side and B-side services, device discovery across routers and auto command generation across the entire network.
-
product
Test Package
Shenzhen Bonad Instrument Co., Ltd.
We can provide a variety of different specifications of freezing load test packages, including AHAMHRF-1 2007/ SASO 2664-2007 Sawdust freezing test package, AS1731.4-2003 Australian frozen Load Test Package, AS72-2005 North American Commercial Refrigeration Load Simulation Test Package, IEC 62552 Test Package for Freezing Load Testing in Refrigerators. In addition, we can also provide customization according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
product
PCI Precision Resistor Card 4-Channel, 2Ω To 13.6kΩ
50-297-131
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Arbitrary Waveform Generators
Helps you to generate with confidence waveforms of almost any imaginable shape: complex signals like digital modulations, RF stimuli for functional and performance tests, radar simulation, optical communication and electronic warfare can be created through an easy to use interface.
