Filter Results By:
Products
Applications
Manufacturers
Shock wave
short moment intense amplitude faster than sound wave
See Also: Wave, Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave
-
product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
product
Acoustic Scoring System
AcoustiScore
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
product
The Nanomotor®
The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.
-
product
Pressure Sensors For Blast Testing
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
product
Hydraulic Vertical Shock Test System
KRD10 series
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Pneumatic Horizontal Shock Test System
KRD12 series
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Pneumatic Vertical Shock Test System
KRD11 series
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
product
Environmental Testing
Environmental testing capabilities include: High and Low Temperature Testing including Thermal Shock. Humidity Testing to 100% Relative Humidity at High and Low Temperatures. Altitude Testing to 100,000 Feet. Combined Vibration, Temperature and Altitude Testing. Mass Spectrometer for Leak Testing. Vibration Testing to 50 G's and 3000 Hz including Resonance Scan, Cycling, and Endurance. Free Fall Half Sine Wave Mechanical Shock Testing to 100 G's
-
product
Gas Chromatograph
Weshine Electric Manufacturing Co., Ltd
The Oscillator shocks and heats up the oil sample to get the gas from the oil. And then inject the gas sample into the GasChromatograph. Before that,we should use the Air Generator and Hydrogen Generator to fire the FID1 and FID2.The Gas Chromatograph will analysis the gas sample automatically, and you will see the gases components waves on the software on PC.
-
product
Bump Tester
KD-163
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Shock Test Systems
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
product
Shock Testing
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
-
product
Shock Test
Shock testing determines the ability of equipment to withstand the infrequent non-repetitive shocks encountered in handling, transportation, and service and to continue to function, where required. Also, shock tests verify that equipment will not detach from its mounting during these tests.
-
product
Wave Soldering Machines
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
product
Radar Systems / Millimeter Wave Radar / Micro Wave Radar
KEYCOM develops various radars for versatile applications based on its knowledge and expertise on millimeter wave and microwave technologies. KEYCOM’s product line of radars includes Radar Test Systems (RTS) to evaluate distance accuracy or output, Radar Alignment Systems (RAS) to help you adjust the alignment of radars, and Radar Cross Section (RCS) measurement systems to measure RCS of such radar targets as aircraft, ships and automobiles.
-
product
Mm Wave Measurement
Erickson PM5B
bsw TestSystems & Consulting AG
Erickson PM5B from VDI, which has been further optimised in the version just presented. The measuring head of the PM5B operates in the WR10 band, i.e. in the 75 - 110 GHz range. High-precision accessories, so-called tapers, provide for adjustments and thus make measurements in the waveguide bands, currently up to WR0.34 beyond 3 THz, possible.
-
product
Thermal Shock Chamber
Wewon Environmental Chambers Co, Ltd.
Makes it possible to quickly and autonomously transfer test items back and forth repeatedly between a hot and cold environment.
-
-
product
Shear Wave Transducers
At Precision Acoustics, we manufacture normal incidence shear wave probes at 1 MHz, which can be coupled directly to an object through a shear wave coupling gel.
-
product
Pressure Based Waves
5218
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
product
Shock and Vibration Testing
E-Labs Shock and Vibration Department can perform testing on a wide range of components such as military, aerospace or automotive. The testing can be performed at ambient or extreme temperature conditions to meet any test requirements.
-
product
901 Shock Testing
Environment Associates performs high-impact mechanical shock for all grades, classes and types of Navy ship board machinery, equipment, systems and structures. Our lightweight shock machine is approved by the Naval Surface Warfare Center for use in testing the survivability of Navy shipboard equipment to MIL-S-901D on items and fixturing weighing up to a combined 500 lbs.
-
product
Ring Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Heavy Industrial Shock Absorbers
The heavy industrial shock absorbers from ACE top off the company's offerings in damping technology. This ACE category gives Designers a choice between self-compensating and adjustable machine elements.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
Long Wave Infrared Cameras
Calibir DXM640 Series
The Calibir uncooled Long Wave Infrared camera platform offers outstanding shutterless imaging performance and is optimized for Size, Weight and Power (SWAP). The Calibir DXM640 series features both shutter and shutterless operation and rapid image output on power up while delivering uniform response over the entire operating temperature range, making it ideal for thermal imaging applications requiring uninterrupted image acquisition. ULIS’s gen2 sensor offers an improved NETD and the updated calibration include customized gain correction on a per lens basis to offer even better image performances and response uniformity.
