Filter Results By:
Products
Applications
Manufacturers
- Advanced Telemetrics International
product
Prop Shaft Torque Measurement Systems
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
product
Field Balancing Software
DS-0227A
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
product
Shaft Alignment
EVO
The evolution of laser shaft alignment towards simplicity and confidence continues with the EVO.
-
product
Slide Gate & Shaft Position
All six Shaft Angle Position Feedback Monitors in the SG1000 Series utilize absolute rotary encoders to provide independent and accurate feedback of a slide gate's or a valve's position to an external device such as a PLC or optional PM500 Process Meter Display Unit. Models are housed in a rugged, Explosion-Proof/Dust-Ignition Proof cast aluminum enclosure that is dirt, dust, grease-proof, and water resistant. In the case of a power failure, all SG1000s are designed to retain accurate gate position.
-
-
-
-
product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Digital Tachometer
TAC-L
Model TAC-L Portable Digital Tachometer measures rotational speed either by contacting a rotatable head to the shaft of the object, or using photo sensor to detect the reflections from the laser. The laser target can record from a distance of up to 20 inches and gives a more accurate measurement than LED targeting. Model TAC-L includes a large LCD with a backlight for use in dark areas.
-
product
Rotary Position Sensors
Using the same technology as our linear range but with a printed rotary coil opposed to the wound linear coil our rotary sensors offer the same high performance as the linear sensor range but with shaft driven rotary or gravity driven tilt measurement. The standard P500/P502 rotary sensors can be manufactured with a measurement range anywhere between 5 and 160. We also manufacture miniature rotary sensors such as the P501 and P505 and the P503 flat PCB style version for customer application fitment. Like our linear sensor range our rotary sensors are also customisable should the standard range not accomodate your application.
-
product
Measurement
Tachometer
Tachometer is used for measuring the rotation frequency of shafts in machines and mechanisms, as well as for calculating the number of complete revolutions. Typically, for measuring the rotation frequency, optical or induction rpm sensors are used.
-
product
3, 2 or 1 Channels, 0.5 VA, 1.5 VA or 3.0 VA
DLx
Linear Variable Differential Transformer (LVDT) and Rotary Variable Differential Transformer (RVDT) are transformer-type voltage/current transducers that convert a linear/rotary movement of a core/shaft to a multi-wire differential AC electrical signal. Both deliver signals linearly proportional to the position of a shaft (magnetic induction core). An LVDT/RVDT simulator is used to convert digital positional commands to corresponding AC signals.
-
product
Dynamic UPS
ROTOBLOC® RBT SERIES 400 - 2000 kVA
The RBT system consists of a standard synchronous generator with no special windings and a simple steel flywheel. The low speed shaft extends bearing life and reduces maintenance. The ROTABLOC® machine is very robust as critical functions do not use fragile components such as power electronics, power capacitors, electro-chemical batteries, active magnetic bearings, electro-mechanical or mechanical friction clutches.
-
product
Inductive Motor Control
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
product
Motors
Pittman and Haydon Kerk motor lines span a wide range of sizes in brushed, brushless and stepper motor technologies. We provide rapid turn-around for prototypes and production orders. Custom designs and special engineering requirements such as special shaft diameters, lengths and mounting flanges are welcome.
-
product
Laser Trackers
Radian Series
The smallest, lightest, most accurate laser measurement tool. API’s compact and rigid UNIBODY tracker design allows for shaft mounted motors, encoders and laser. The UNIBODY shaft mounted laser innovation minimizes Abbe offset errors, while also housing laser source, optics, camera and major head electronics in the center of the tracker body.
-
product
Rotary Motion Logger Sensor
NUL-226
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
product
Non-Contacting Multiturn
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
-
product
Rotary Position Sensors -AEC- Q200 Compliant
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
product
Water Level, Stage, and Flow Sensors
Campbell Scientific offers a variety of sensors to measure water level, stage, and flow: pressure transducers, shaft encoders, radar ranging sensors, sonic ranging sensors, and bubblers. Users often select their sensors based on the site location, required accuracy level, and ease of installation.
-
product
Oral Probe
OT-1
The OT-1 oral temperature prove for humans is re-useable and has a fast response time.• Fast reading oral use, with accuracy to 0.1°C .• Smooth ball tip. Stainless steel shaft - 3'' long, .050'' diameter. Tip diameter 1/8'', 5 foot lead length. Time constant 0.8 seconds.
-
product
Pulse Generator
Digital Ring Kits
NEMA C frame rings provide mounting for 1101, 1201, and 1202 shaft speed sensors for use with 199SM magnet wheels on motors with NEMA C frames. The DRK (Digital Ring Kit) Series provides a single-channel output and the QDRK (Quadrature Digital Ring Kit) Series offers a bi-directional output. Kits include mounting ring, hardware, magnet wheel, and sensor.
-
product
Mechanical Counter
SP101/102 Series
The SP-101/102 Series is a heavy duty totalizer. It has a double sided shaft for stability. Available in Revolution or Rotary type movements. Input shaft direction is choice between top going or top coming. Count speed range from 300 ~ 3000 rpm. It is a available in 4 or 5 digits with a large digit size of 6.0 x 4.0mm. Resetting of count value is done easily with the front push button reset.
-
product
SpeedMaster
The SpeedMaster™ is the only device that accurately tests the calibration of a speed switch, and allows testing of the alarm and shutdown features of the sensor while installed on the machine shaft.
-
product
Transmissive Rotary Codewheel
HUBDISK-2
US Digital offers a wide variety of standard hub / disk assemblies (optical encoder disks attached to an aluminum hub) to aid with mounting on a shaft. Encoder disks may also be ordered as a stand alone item (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable.
-
product
Torque Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
product
Encoders
*Designs to proven industrial standard*Compact and robust housing*Hollow shaft encoder for direct mounting on actuators*Versions with integrated fieldbus interface*Cable entry for axial and radial use
-
product
Wireless Hazard Monitoring
When it comes to hazard monitoring, we know it simply has to work. HazardPRO was designed from the ground up to provide turnkey, reliable, and consistent protection for your most valuable assets—products, facilities, and most importantly, people. Consistent operation is ensured with built-in tools such as self-diagnostics, transmission logging, and redundant radios providing you confidence that your critical processes are being monitored and logged at all times. Wireless nodes utilize temperature (bearing, ambient, and stud), RPM shaft speed, alignment, and vibration sensors. Ambient Sensors ensure bearing and alignment measurements are relative to the surrounding environment.
-
product
Development Test Stands for Electric Motors
Development test stands from imc are characterized by high flexibility in electric motor trials. A comprehensive variety of motor types can be tested and a complete range of tests carried out. The mechanical configuration consists of a test bed with a load machine and a torque measuring shaft. The load machine and torque sensor shaft are mounted on a linear guide and precisely aligned axially by means of laser. It can be moved towards the test object on ball bearings, as a complete unit. Especially time-saving: no need to realign the load machine assembly when changing the torque sensor.
-
product
Shaft Speed Switches
A speed switch senses rotating shaft speed, comparing it to one or more settable over/under/zero speed alarm trip-points. A shaft speed sensor detects magnets embedded in a shaft-mounted pulser wrap/disc. As the shaft rotates, the passing magnets are detected across an air-gap as pulses with frequency proportional to shaft RPM. When a conveyor belt or bucket elevator begins to slip the pulse frequency (shaft RPM) crosses to the alarm side of a trip-point threshold, a corresponding relay de-energizes, providing shutdown or alarm.
