Filter Results By:
Products
Applications
Manufacturers
SFP
is a multi-source agreement (MSA) transceiver used in communicaitons.
See Also: SFP Test, SFP+, Transceivers
- Virginia Panel Corporation
product
VTAC Wired
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The results show no significant deviation from the SFP signal until approximately 6.25 GHz. Even at 6.25 GHz, there is only -1dB of difference between the two patchcords, which is approximately a 10% loss. With signal integrity playing such an important role in high speed testing, the obvious choices for high bandwidth data testing are VTAC Wired products.
-
product
SFP+ Cable, 1m
784076-01
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
FMC Card with Four SFP+ 10 GBit Ports
TEF0008-02
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 GBit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.
-
product
CWDM SFP Transceiver Tester for Installation & Verification
ZonuCheck
Hand held instrument combines: Transceiver Tester (Tx power and Rx sensitivity),CWDM (Wavelength selective) Optical Power Meter, Media converter (enables GbE connectivity to bypass customer CPE) and datalogger. The new Tester makes the installation, service and maintenance of an SFC Access Network a ?snap? for Field Technicians. Optimized for our SFC Transceivers and Passives, the ZonuCheck? Handheld Tester may be used in any CWDM application to identify ITU CWDM Wavelengths and measure the Optical Power levels for the ten (10) commonly used ITU CWDM Channels.
-
product
24 Port CPCI Managed Layer Two Switch
CP217
The CP217 is a 6U single slot Compact PCI (cPCI) module that has 24 ports of GbE. Eight ports via RJ-45 and four ports via SFP as a single slot. The Module come with an optional daughter board which has an additional 12 ports of GbE via SFP which can provide Fiber or Copper interface.The switch is managed via http and supports a rich set offeatures such as VLAN, Spanning tree, QoS, Mirroring, etc.
-
product
Gigabit Ethernet
10G Transceivers: SFP+, XFP, X2, XENPAK
10G transceiver modules from M2 optics are available in a range of types including SFP+, XFP, X2, and XENPAK. All types meet industry standards and we can offer Cisco-compatible along with other major brands.
-
product
PXIe Vector Network Analyzer Source, 1 MHz To 6 GHz
M9389A
The M9389A PXIe vector network analyzer source is a component for the M9485A PXIe multiport vector network analyzer. The M9389A configuration includes two PXIe modules (M9310A source output, M9309A synthesizer) and its control is provided through the M9385A software front panel (SFP). The M9485A provides a true multiport VNA with up to 12-ports in one chassis and up to 24 ports in two chassis.
-
product
1U Rackmount Network Appliance Platform With Intel® Atom® Processor C3558/C3758 And Up To 10 LAN
NA362R
The NA362R is powered by the Intel® Atom™ processor C3558/C3758 (Codename: Denverton). The low power 1U network appliance comes with six 10/100/1000 Mbps LAN ports and two or four 10 GbE SFP+ fiber ports. It is equipped with one pair latch-type LAN Bypass function for fail-over option as well as featuring BIOS console redirection. Furthermore, it supports the Intel® QuickAssist Technology which accelerates data processing and compresses cryptographic workloads. The network communication appliance also features the Intel® Data Plane Development Kit, which greatly boosts packet processing performance and throughput to improve data plane performance.The NA362R comes with four DDR4 R-DIMM/U-DIMM sockets that can provide system memory of up to 128GB and support both ECC and non-ECC memory types. It comes equipped with two 2.5" SATA3 HDD and one mSATA for sufficient storage. In addition to six 10/100/1000 Mbps LAN ports (Intel® i210 Ethernet controller), it also has options of two or four 10 GbE SFP+ fiber ports for high bandwidth and long-distance communications. I/O options also include two USB 2.0 ports and a serial console port. To ensure reliable operation, the 10-port network platform supports watchdog timer. Moreover, it also supports mainstream Yocto and Linux.
-
product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
product
AS5653 Compliant Small Form Pluggable (SFP) Transceiver
XCVR-AS5653
Avionics Interface Technologies
AS5653 SFP transceiver that can be inserted into any standard SFP slot - 1.0625 GBPS communication signals interface using TNC connectors - Bulkhead mountable female TNC connector at the end of a 1 meter length of RG179B/U - 100 feet of RG179 operates to better than 10E‐13 Bit Error Rate - Available for 75 Ohm single ended copper or 150 Ohm Differential
-
product
1000BASE-T1 MEDIACONVERTER EMC
Art.-Nr.: TE-1404-1
The ideal solution for working quickly and efficiently with 1000BASE-T1 EMC measurements The 1000BASE-T1 MediaConverter EMC is especially designed for measurements within the EMC chamber. It is delivered in a Set with an adapter board which enables internal PHY status readings and provides one point-to-point connection between Automotive Gigabit Ethernet and SFP Gigabit Ethernet, with which optical fibre modules are used.
-
product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-4x10G SFP+
- Support up to four 10GbE SFP+ interfaces- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
product
Fiber Tranceivers
Wuhan Sunma Technology Co., Ltd.
Active Optical Cables, Fiber Optic Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP).
-
product
Dual-Port HS-1760 Test & Simulation PXI Express Module
PXIe-C1760
Avionics Interface Technologies
3U PXI form factor fits into PXIe or PXI hybrid slotTwo independent ports programmable as NC or NT(s) simultaneouslyTwo SFP sockets accepts FC-0 AS5653 or AS5625/AS5627 transceiversSupports NC-to-NT transfers, NT-to-NC Transfers, Mode Codes, and BroadcastFull control of sequence and exchange managementSupports large file exchangesFull Monitoring of all Bus TrafficTriggering and FilteringFull Error InjectionSupports DMA for high speed streaming of data to/from the boardIRIG-B Time Code Encoder/Decoder for Data CorrelationOptional Special FC-0 physical layer compliance with SAE AS5653Optional fcXplorer Analyzer for decoding HS1760 frames
-
product
Network Interface Card
XMC477RC
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
-
product
100Gbps Ethernet Packet Generators
Axtrinet (AXTRINET IS A TRADING NAME )
1x 100GbE QSFP28 port, 4x 25GbE SFP28 / 10GbE SFP+ / 1GbE SFP ports, Status Indicators
-
product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
product
40Gbps Ethernet Packet Generators
Axtrinet (AXTRINET IS A TRADING NAME )
40Gbps QSFP+ & 10Gbps SFP+ ports, Support optical & copper transceivers, Wire-rate performance on all ports, Compact & Portable, Intuitive Graphical Control Interface, Control multiple units from single GUI, Test Automation with TCL interface
-
product
Fiber Optic Connectors & Cages
Pulse Electronics Networking BU supplies high-quality fiber optic connectors and cages to innovative ODMs, OEMs and other manufacturers designing today’s most demanding network products. Our line of 40+ fiber optic connectors include SFP, SFP+, and QSFP connector and cage products.
-
product
SFP
4 Gbps
Is specifically designed for high performance integrated duplex data link over multi mode optical fiber. The high-speed oxide VCSEL and photo diode are provided as a light source and a detector, respectively.
-
product
Fiber Cable, Multimode, OM3, 100m
784184-100
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
product
Ethernet To Fiber Optic Converters (Multi-Drop)
Our advanced, rugged, industrial-grade, Fast and Gigabit Ethernet to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the Fast and Gigabit Ethernet data up to 100 miles or 160 km. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the Ethernet data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire Ethernet network more robust and reliable. These Fast and Gigabit Ethernet to multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
product
1000BASE SFP Transceivers
CommFront offers a range of high-quality, high-performance SFP transceivers ranging from MM 850nm / 0.3 miles (550m) to SM 1550nm / 100 miles (160km). SFP (Small Form-Factor Pluggable) is a compact, hot-pluggable network interface module used for data communication and tele-communication applications. SFP equips with one or two fiber optic connectors (e.g. LC connectors) for connecting a fiber optic cable or sometimes an RJ45 connector for connecting a copper cable. Because of its compact size and flexibility, many Ethernet Switches come with SFP ports so individual ports can be equipped with any suitable type of transceiver as required.
-
product
Configurable & High Density Signal Transport
VF-9000 Series
Life on a mobile production truck or ENG van means making the most of your surroundings. With limited real estate for technology, our customers need high-density platforms to manage the abundance of signals coming in and going out. MultiDyne’s VF-9000 Series is built for high-pressure sports, news and live event production scenarios, and high-capacity transport requirements between studios and across campuses. The VF-9000 Series is also remarkably intelligent, providing automatic configuration of video inputs and outputs based upon recognizing which VF-9000 SFP modules are added to the frame. Hot-swappable modules establish redundancy to ensure live mission-critical operations are never disrupted, while data transport, video signal regeneration and wavelength shifting add value for users seeking a brute-force, rock-sold signal trunking and fiber transmission solution.
-
product
Bit Error Rate Tester
Eye-BERT Gen2
The Eye-BERT Gen2 builds on our original Eye-BERT, adding extended data rates, mixed mode testing capability, and a color touch screen. The extended data rate allows for testing of links in the 125Mb to 11.4Gb range all in a single unit. The Eye-BERT Gen2 offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of SFP and SFP+ transceivers as well as link verification and performance testing all in a single unit.
-
product
Gigabit-SFP Transceivers
SFP Transceivers are designed for use in Gigabit Ethernet and to provide an IEEE-802.3z compliant link for 1.25/2.5Gbps short or long reach applications.
-
product
16 Channel VME Digitizers
SIS3316
With the SIS3316 you have the option to use an Ethernet SFP or an optical SFP medium to implement non VME readout.
-
product
COM Express Type 7 Development Baseboard
CEB94701
*Two 10GBASE-KR SFP+ ports*2 SATA-600*VGA*4 USB 3.0*2 PCI Express Mini Card slots*2 RS-232/422/485
-
product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
product
Mini Media Converter
MX Series
The MX mini media converter provides one RJ45 10/100/1000Base-T connector supporting auto-negotiation, MDI/MDI-X, full-duplex and half-duplex. The other connector is a 1Gbps SFP slot, suitable for any 1Gbps SFP module.
