Filter Results By:
Products
Applications
Manufacturers
SCADA
Supervisory Control And Data Acquisition
-
product
Fire, Gas & Intruder Controllers & Alarms
MultiSafe-MX
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
product
Protocol Converters
Applied Systems Engineering, Inc
ASE provides a total solution approach to the area of protocol test equipment with its’ family of PC based protocol test products. The ASE2000 RTU Test Set is a full-featured protocol test unit that provides the user with a powerful and flexible tool for testing and maintaining SCADA RTU and SCADA IED equipment and diagnosing communication problems.
-
product
Recorder Carrier Device
RCD
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
product
SCADA
Schweitzer Engineering Laboratories, Inc.
SEL SCADA systems offer improved reliability and performance, streamlined access to valuable information, and expanded power system management capabilities.
-
product
Integration
Schweitzer Engineering Laboratories, Inc.
Integrate protective relay and metering information into SCADA and plant control systems through secure networking and automation devices.
-
product
Modbus Diagnostic Program
Modsak
Modsak is a versatile Modbus diagnostic program. It will be of interest to device manufacturers, software developers, system integrators and field service engineers. Modsak can be used to test or simulate almost any device or system that uses the Modbus protocol: slave devices, PLC's, HMI's, MMI's, DCS's, RTU's, SCADA systems, bridges, gateways, device servers, etc.
-
product
RTU (Remote Terminal Unit)
R2+ RTU
*The R2+ Remote Terminal Unit (RTU) is a distributed architecture and large I / O capacity designed to meet the various demands of current Power SCADA / EMS applications.
-
product
Receivers
Pig tracking sensors are utilized to indicate the passage of a pig past a given point in the line. This system can be linked to a SCADA package or simply used to provide an easy to see visual indication.
-
product
Digital Instruments and Measuring Transducers
Digital instrumentation devices are installed to display an electrical or process variable, for rapid monitoring and management, normally in industrial settings. This information can be used to detect any alarm that may be triggered by a control value, informing in real time of any malfunction in an industrial, machinery or control system process. The data is shown numerically, and is proportional to the measured parameter and can be integrated into SCADA systems, as long as they have integrated communications.
-
product
Three-Phase Relay Test Set
CMC 353
With its compact design and low weight of 13.3 kg / 29.3 lbs, the CMC 353 provides the perfect combination of portability and power. It is the ideal test set for three-phase protection testing and the commissioning of SCADA systems. The powerful current outputs (3 x 32 A / 430 VA) optimally support 5 A relay testing.
-
product
Modbus PLC Simulator
This protocol simulator started one weekend as a test program while developing a SCADA/HMI with modbus RTU and TCP/IP and afterward came in useful testing an embedded gnu-Linux device too. It has worked so well for me, I decided to put a nice GUI onto it and release it for free. The modbus protocol, also called open-mbus is implemented in many process control and monitoring devices, while most SCADA or HMI systems have a driver.
-
product
SCADA Communication
From a technical point of view, communication is the process of exchanging information between a transmitter and a receiver. To achieve this, the transmitter encodes a message and transmits it to the receiver. The receiver can only decode the message if it knows the protocol. The setup of the communication between A. Eberle IED's (Intelligent Electronic Device) and a SCADA system becomes more easy if all partners communicate in such a way that all queries regarding the protocol are clarified before or during the system design process (at latest before commissioning).
-
product
Master And Slave
Smart I/O
An I/O server is a software which controls and monitors one or more PLCs /RTU's using various communication protocols.Our I/O servers are built on highly optimized Windows 32bit platform. They are capable of handling very large scale SCADA systems with minimal impact on CPU usage, resulting in effective timing and usage of available hardware.Currently, we have Master and Slave solutions for DNP3 and Modbus (ASCII, RTU, TCP). Please select the appropriate tab above for more informaiton.If you are looking for a specific I/O Server, please contact us with your needs.
-
product
Panel PCs
The Senses panel PC range is our own brand of entry-level to high performance panel PCs. These systems provide affordable and reliable quality flat panel PCs and are used in Human Machine Interface (HMI), SCADA, process control, factory automation, building control and home automation applications.
-
product
Datalogger
iLOGPlus
Infinite Industrial Informatics Lt
iLOGPlus RTU/Data Loggers are internet enabled devices, specially suited for remote data acquisition, distributed telemetry and remote control. The units act as master devices and send alerts and data files on their own via FTP, email and SMS. All types carry a built-in TCP/IP webserver with live webpages that can be accessed by any Internet browser application. They accept and serve TCP and SMS commands for interactive operation in a SCADA system.Analog inputs and digital I/O are expandable by means of I/O expansion modules, plugging on a serial I/O expansion bus.
-
product
Data Gateway
SCADA
The SCADA Data Gateway can be used as a data concentrator or a data translator or both at the same time. Check out the features of this advanced, yet affordable Gateway.
-
product
SCADACore Cloud-Connect
SCADACore’s Cloud-Connect products bridges your sensors and field operations to our fully-managed Web SCADA solution. SCADACore delivers complete end-to-end solution to bring field data to you anytime, anywhere.
-
product
C Series PROFINET Interface Module
The C Series PROFINET Interface Module provides two PROFINET interface ports that enable you to reliably connect programmable logic controllers (PLCs), I/O, sensors, and drives over long distances in industrial environments. PROFINET is an application protocol that uses familiar concepts from PROFIBUS that are implemented on the physical layer of Ethernet. The C Series PROFINET Interface Module includes NI-PROFINET driver software for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces.
-
product
Automation Control
Schweitzer Engineering Laboratories, Inc.
Monitoring and controlling substation power systems requires comprehensive solutions. SEL’s complete solutions and hardened devices help maintain system stability with deterministic control; streamline access to valuable IED data, communications processors, and field devices; and improve visualization and control with local HMIs and access to SCADA systems.
-
product
Visualization And Analytics
Schweitzer Engineering Laboratories, Inc.
Diagnose relay behavior during a power system fault while gaining system insight that is not possible with SCADA.
-
product
cRIO-PN-S, Slave, C Series PROFINET Slave Interface Module
782131-01
Slave, C Series PROFINET Slave Interface Module - The cRIO-PN-S connects NI programmable automation controllers (PACs) to PROFINET industrial networks as powerful slaves. The interface includes the NI‑PROFINET for CompactRIO driver for human machine interface (HMI) and supervisory control and data acquisition (SCADA) applications. You can perform PROFINET device automated test using these interfaces. The cRIO-PN-S is only compatible with CompactRIO systems.
-
product
Communication Protocol Test Harness
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
product
Generation Control
Schweitzer Engineering Laboratories, Inc.
Safely operating a generating facility requires reliable automation solutions that can integrate with relays, SCADA, and plant controls. With a generation control solution, you will realize operational efficiencies and increased reliability.
-
product
Temperature Measurement Devices
Qualitrol's line of Direct Mount Thermometers provide an accurate indication of temperature with a rugged, low profile design, multiple control and alarm functions with optional SCADA output
-
product
Electrical SCADA Monitoring
Model-driven SCADA & Monitoring provides an intuitive real-time visualization and analyses platform via intelligent graphical user interface, one-line diagram, geospatial view, and digital dashboards.
-
product
Industrial Ethernet
PLANET Industrial Ethernet equipment is compliant with various industrial protocols and ITS certifications such as MQTT, Modbus, SCADA, EtherCAT EN50155 and E-Mark to meet all the transmission needs, be it Information, Control or Device. PLANET features ERPS Ring, IEEE 1588 PTP, Layer 3 routing, 10G transmissions, cybersecurity and more to ensure high performance and security of our comprehensive Industrial Ethernet collection.
-
product
Power Line Transducers
Current Transducers measure AC Current and converts it to an industry standard output signal which is directly proportional to the measured input. These Transducers provide an output which is load independent and isolated from the input. The output can be connected to Controllers, Data-Loggers, PLC''''s, Analog / Digital Indicators, Recorders for display, analysis or control. They are ideal for SCADA, Energy Management, Telemetering for Remote, Local as well as Central Monitoring Systems.
-
product
Mobile, Hardened Test Set
MBX1
With the MBX1 platform and our software, you can easily test SCADA and substation automation systems (SAS) in a highly secure way. The mobile solution allows you to perform quick assessments and temporary monitoring, e.g. during commissioning.
-
product
WebAccess SCADA Software
Advantech WebAccess is a web browser-based software package for HMI/SCADA software. All the features found in WebAccess HMI/SCADA software including SCADA Server, Widget Library, Excel Reporting, Remote Device Management, Animated Graphics Displays, Real-time Data.
-
product
IoT I/O Gateways
ADAM-6700 WISE-Edgelink
Intelligent IoT I/O gateways with WISE-EdgeLink and Analog, digital or relay I/O connect edge to the AWS cloud, SCADA through MQTT, SNMP, RESTful, 4G.
