Filter Results By:
Products
Applications
Manufacturers
Prototyping
Construction of first working designs.
- Pickering Interfaces Inc.
product
PXI Prototyping Module, 2-Slot, 37-Pin D-Type
40-225A-202
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Prototyping Module, 1-Slot no Connector
40-225A-001
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785595-01
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
product
Dynamic Test Board Vehicle Simulator
DTB
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
product
Custom Test Connectors and Sockets
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
product
PLCC-to-DIP Adaptor
Series 652000/653000
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Ideal for prototyping and testing/evaluation. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Lifecycle Support for Custom Product Development
The parts and components that are rooted in idea generation and product development are the ones that are most likely to succeed. Electri-Cord’s lifecycle support for the production and manufacturing of custom wiring harnesses, cable assemblies, power cords, and high-level assemblies incorporates a four-stage approach that covers the lifespan of the product. This custom product development process includes everything from design prototyping to end-of-life processes.
-
product
Prototyping & Test Consulting Services Solutions
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
LIN Interface Device
LIN Interface Devices are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. LIN Interface Devices work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
2-Slot 64-Bit 6U CompactPCI Backplane
cBP-6402R
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
product
PXI Prototyping Module, 1-Slot, 20-Pin GMCT
40-225A-801
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Electrical Development & Redesign
Your product description goes hereARC’s electrical engineering team has the leg up when it comes to developing or redesigning to your specific requirements.All the way from prototyping to cable design to integration, our talented team of clever engineers can deveop a prototype quickly and get your project off on the right foot. Whether it is a new solution or if you are redesigning an obsolescent FPGA system, our team can provide quickly and effectively while still keeping your budget in mind.
-
product
COM Express Type 6 Prototyping Kit Based On Intel® 12th Gen Core™ I5-12600HE
COM Express Type 6 Alder Lake-P
The COM Express Type 6 Alder Lake-P is a powerful COM Express Type 6-based IoT solution development kit powered by Intel 12th Gen i5-12600HE 12-core (4 P-core + 8 E-core) SoC with integrated Intel Iris Xe GPU graphics (80 execution units) and comprehensive high speed interfaces.
-
product
Support Services
Libra offers our customer a full suite of support services to help manage your product across the entire product life cycle. One of the most important aspects of our partnership with our customers is a robust supply chain management solution. We have spent decades building our partnerships with our valued suppliers, to offer you an extensive supply chain you can rely on. Over the years, Libra has invested heavily in systems and sophisticated data analytics, to intelligently manage that supply chain and link it to you product and schedule requirements. At the front end of your product’s life cycle, we offer rapid prototyping, full NPI support and strong DFx capabilities, to assist in making your product cost effective, quality driven and highly manufacturable. We also offer a full suite of RMA and warranty support services to support your product through its entire life cycle.
-
product
Silver Button Sockets
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
product
PXIe-8510, 2-Port PXI Vehicle Multiprotocol Interface Module
784121-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Interference Lithography Gratings
Interference lithography is an optical nanolithography technology for the fabrication of extensive periodic nanostructures. Critical dimensions of less than 50 nm can be realized. At AMO two interference lithography tools are installed. One setup for extensive, high quality gratings with fixed periods, the other more flexible tool allows quick prototyping. We offer grating fabrication on silicon, silicon dioxide and other substrates with tailored pitch, etch depth and size.
-
product
Electronics Manufacturing Services
EMS
A production consignment service that develops based on know-how and technological capabilities of "MONOZUKURI " that we have cultivated over many years. Full support from design to board mounting, prototyping, manufacturing, maintenance. We respond to various outsourcing needs such as customer's design consignment and production consignment.
-
product
Chassis & Subsystem Pre-integration
Mercury’s broad ecosystem of compute building blocks enable SWaP-efficient solutions to be quickly configured within a low-risk environment. Our off-the-the-shelf chassis facilitate rapid development work and prototyping to support concurrent engineering initiatives.
-
product
PXI FlexRay Interface Module
PXI FlexRay Interface Modules provide two fully functional FlexRay interfaces, allowing an individual electronic control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. PXI FlexRay Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
Network Management
C Agent
WebNMS SNMP Agent Toolkit C Edition is a rapid prototyping and development tool to build SNMP (SNMP v1, SNMP v2c and SNMP V3) agent, TL1 agent, and CLI agent in ANSI C. It helps network engineers and telecom application developers to create standalone or multi-protocol agents with SNMP, TL1, CLI and HTTP support based on application requirements.
-
product
Rapid Prototyping Solution
SFINX
SFINX® is a rapid prototyping solution that enables customers to rapidly test an idea, concept or application, using equipment compatible with rolling stock requirements.
-
product
*C Series CAN Interface Module
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785166-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
RS LabSite® modulogic
RS LabSite® modulogic is a comprehensive and adaptable software suite conceived for introducing service loads into individual components or complete vehicles, or performing calculations within the framework of Virtual Prototyping (standardized loadsequences, virtual generation of load data). This enables you to stay in full control of all tasks that follow the acquisition of measurement data in the proving ground.
-
product
PXI, CPCI Development And Prototyping Board
TE2100
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
product
LIN Interface Module
C Series LIN
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
