Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 10A Power MUX, 2-Bank, 8-Channel
40-661-102
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
-
product
VME Bus Tester
VBT100
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
Optical Light Source
STC-OLS201 series
Shanghai Stone Communication tech Co., Ltd
a simple and cost-effective fiber optic tester,it is usually used together with fiber optic power meter to measure the optical loss on fiber cables. STC-OLS201 series light source provide multiple wavelength output, the wavelengths can be required on customer specific requirements (the Max wavelength is 5, such as 850/1300/1310/1490/1550nm).
-
product
CWDM SFP Transceiver Tester for Installation & Verification
ZonuCheck
Hand held instrument combines: Transceiver Tester (Tx power and Rx sensitivity),CWDM (Wavelength selective) Optical Power Meter, Media converter (enables GbE connectivity to bypass customer CPE) and datalogger. The new Tester makes the installation, service and maintenance of an SFC Access Network a ?snap? for Field Technicians. Optimized for our SFC Transceivers and Passives, the ZonuCheck? Handheld Tester may be used in any CWDM application to identify ITU CWDM Wavelengths and measure the Optical Power levels for the ten (10) commonly used ITU CWDM Channels.
-
product
Multi-Channel Power Module
67394
The 67394 Multi-Channel Power Module is a new generation of compact, stable and high reliability AC to DC power supply that can test the small size panels. It has multiple power sources with voltage/timing adjustable functions, protection functions and measurement circuits. Its modular design can work with FPD tester and PG card to provide standard power source for testing the panels.
-
product
Leaking Current Meter
7610B
Peaceful Thriving Enterprise Co Ltd
This is a stable, low power consumption, and high accuracy 3 1/2 digits (2000 counts) leaking current tester for automobile. Leaking current for automobile is generally as small as milliamps, which is hard to measure by clamp meter. By plug this meter with the fuse box, user is able to measure leaking current as small as 1 mA.
-
product
Test System
LB301
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
FPD Tester Model
27014
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
product
Smart Surge Protectors
SSP-30X
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use, Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
product
Network Tools & Testers
Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).
-
product
Universal Launcher Test Set
TS-217
The TS-217 is an I-level and Depot-level Universal Launcher test set supporting fighter aircraft launchers including the LAU-127, LAU-128, and LAU-129 (AMRAAM), LAU-117 and LAU-88 (Maverick), and LAU-7 (Sidewinder) missile launchers, launcher electronic assemblies, launcher power supplies, and circuit cards. The TS-217 is also used as a depot-level tester for F-18 armament including launchers (LAU-127, LAU-7, LAU-115, and LAU-116), bomb racks (BRU-32), and aircraft pylons (SUU-62 and SUU-63). Additionally, the TS-217 supports MAU-169 Paveway kits, subassemblies, and circuit cards. The TS-217 performs full parametric functional testing as well as troubleshooting to the faulty LRU (I-Level configuration) and SRU (Depot-Level configuration). The TS-217 can be used as an I-Level tester or as a Depot / Acceptance tester for launcher subassemblies.
-
product
Calibration Services
Mors Smitt has a professional calibration center. All electrical measurement equipment can be calibrated (for example; multimeters, current clamps, temperature meters, installation testers, power meters, safety testers, etc.).
-
product
Universal Pylon Tester
MS 1121
Portable test equipment to check the electrical functionalities of pylons by simulating various store types in aircraft. This system is able to simulate the functionalities of different PIBs (IB/MB/CF, OB & Laser). The system provides facility to test two Pylons in parallel. The tester provides aircraft specific AC &DC voltages and facility to inject discrete inputs for checking output(s) viz firing voltages, fusing voltages. The system provides four channels of RS422 and Two channels of 1553B communication. Portable unit with caster wheels with all required hardware, power supplies, instruments, connectors and laptop housed in it.
-
product
All-in-One Field Optical Tester
SMT-50
Power meter is the best essential tool for all technicians installing or maintaining optical fiber network. SMT-50 Multi Tester is made for the best performance of different parameters and demanding applications on fiber measurement. It is designed for handy size with simplicity and accuracy. SMT-50 provides 4 exquisite functions to optimize the time of all technicians and can be tested at up to 6 wavelengths in operating. Six main wavelengths (850, 1300, 1310, 1490 1550 and 1625 nm) used in FTTX networks can be tested of passive optical networks (PONs)
-
product
Automatic Metallic Pendulum Impact Testing Machine
Jinan Testing Equipment IE Corporation
JB-450/750A automatic type pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and is capable of doing a large number of impact tests continuously. The automatic type pendulum impact tester can display the impact power, impact toughness, and the pendulum's rotation angle. All the testing reports can be printed out. JB-450/750A can be equipped with fully automated sample feeding system, which greatly improves the test efficiency, and reduce labor intensity. The crygenic cooling device is available for impact tests under the lowest temperature down to -196 C. The automatic type pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
Battery Capacity Tester
BLU-T Series
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conducted in an accurate, user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU-T battery load bank enables setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, the BLU-T units can be connected in parallel, or BXL-T additional load units can be linked.The instrument offers a high power-to-weight ratio. BLU-T series has models starting from 12,8 kg / 28.2 lbs and up to 19,2 kW of power.A user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Discharge parameters can be monitored in real-time during the capacity test. A 4,3-inch touch screen shows overall battery voltage, discharge current, discharge test time and capacity during the entire test. Also, the capacity tester is compatible with DV-B Win software. A user can view a detailed numerical and graphical presentation of key parameters, and create reports in various formats.Testing can be carried out without disconnecting the battery from the service.
-
product
Entry Level Loss Tester
Model：OLT-20
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
product
H.V. Proving Unit (DCV)
2713 PU
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
product
Test Technology
GLP3
The GLP3-Windows®-testers are our premium testers to test a variety of different complex products. They are preferably used to test electric component groups, run-in test benches, power supplies, cables, washing machines and more and are ideally suited for complex test benches and inerlinkes assembly- and test lines.
-
product
Xenotest
220/220+
Atlas Material Testing Solutions
The Xenotest 220 and Xenotest 220+ are large capacity lightfastness testers dedicated for textile testing. They come with premium on-rack light and temperature sensor and non-aging optical filter technology. With the ability to test 38 samples, the 220 Series provides nearly twice as much capacity in the same footprint compared to 150S+. The combination of its large test chamber and the efficient use of power and water make it today‘s most economic air-cooled instrument available. It complies to standards ISO 105 B02, AATCC TM16 (option 3), and Marks & Spencer C9, C9A.
-
product
Ground Continuity Tester - 25, 30, 35 AMP
M25, 30, 35
Production / Quality Assurance Testing - Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures ground continuity from ground to the power cord ground pin of the DUT. Interface enables interconnection to any ROD-L Hipot & Leakage testers to form a complete automatic test system.
-
product
Automatic Insulation Oil Tester
KVIO-80
KV Hipot Power Test Equipment Co.,Ltd
Automatic Insulation Oil Breakdown Tester Is Used to carry on power frequency dielectric break down test on the transformer oil, capacitor oil, electric device, insulation tool etc.
-
product
Rail Pressure Tester
RPT-5
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
product
International Wireless 6V/12V Battery and 12V/24V System Tester
SBT1
Schumacher Electric Corporation
PERFORM BATTERY AND SYSTEM TESTS WIRELESSLY FROM YOUR SMARTPHONE OR TABLET.For 6V and 12V automotive batteries (SS EFB and AGM included) and 12V/24V charging/starting systemsEasy and fast Bluetooth® pairing Works with SBT1 SchulinkTM app, which includes eight language settings.Performs Battery Test, System Test, Start-Stop Test and EV Battery Test Email or text test results – stores 2,000 test records Test batteries with as little as 1.5V3 LED indicators (Blue: Connected, Green: Power, Red: Trouble)On/Off button20-inch cable with durable clamps3.7V rechargeable internal lithium ion batteryContents: (1) SBT1 tester (1) Manual
-
product
Trailer Light Tester
Checkmate 1200
Checkmate 1200 is a good, basic light tester for trailer light systems that can also serve double duty to power anti-lock brake systems.
-
product
Instrument Transformers Tester
TE30
Calmet Smart Calibration Devices
Electricity meters tester class 0.05 and 0.1. Three phase tester of current transformers and analyser of power network quality. It makes possible electricity meters testing on the site or in the laboratory.
-
product
Smart Surge Protector
SSP-50X
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use. Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
product
Battery Test & Management
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for testing and measurement of battery from your critical power systems. It includes battery online monitoring system, battery tester for internal resistance/conductance, battery charger, battery load bank, battery data logger, battery charger/discharger and so on.
-
product
Optcal Multimeter ( OPM+OLS)
TM590
TM590 series Fiber Optic Multimeter is a newly designed tester, which integrates the optical power meter and optical light source function in one unit. It can separately work as power meter or light source; or simultaneously work as power meter and light source together.
