Filter Results By:
Products
Applications
Manufacturers
Particle
fundamental objects of quanta.
See Also: Nanoparticle, Airborne Particle, Particle Accelerator, Particle Counters, Particle Detection, Wave
-
product
Electromagnetic Express
EM-X
Is a physics modelling package for electromagnetic fields and charged particles. A CAD component allows the definition of mechanical parts and assignment of electric potentials, magnetization and charged particle sources. A time domain, particle-in-cell (PIC) tool then solves the electromagnetic fields and moves the particles within them. The particles’ own charges andmotions are fed back into the electromagnetic fields allowing the effects of space charge and selfmagnetism to be accounted for.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Nanoparticle Tracking Analyzer
ZetaView®
ZetaView® Nanoparticle Tracking Analyzer for hydrodynamic Particle Size, Zeta Potential and Concentration. With ZetaView® individual particle tracking, classical micro-electrophoresis and Brownian motion are presented as modern analysis tools. Auto-alignment and auto-focusing make the “Seeing is Believing” principle user friendly. By sub-volume scanning robust results of zeta potential and size histograms are derived from thousands of particles.
-
product
Sand & Dust Test
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
product
Radiation Detectors
High Purity Germanium (HPGe) DetectorsSilicon Charged Particle DetectorsScintillation DetectorsORTEC is a leading supplier of solid-state, high resolution, semiconductor radiation detectors. These radiation detectors are used in research, commercial industry, environmental protection, health and medical physics, as well as homeland security to detect gamma-rays, X-rays, and charged particles.
-
product
Aggregation Analysis System For Biopharmaceuticals
Aggregates Sizer
The "Aggregates Sizer" aggregation analysis system enables the quantitative evaluation of particle amounts in the SVP range as a concentration (unit: μg/mL). Aggregations of biopharmaceuticals can be categorized into 3 ranges: IVP (In-visible Particle), SVP (Sub-visible Particle), and VP (Visible Particle), according to their particle size. Until now, no particle size analyzer could cover the SVP range with a single measurement. Therefore, multiple methods had to be used. Aggregates Sizer completely covers the SVP range.
-
product
Zeta Streaming Potential
ZETA-check
Particle interface potentials like the oscillating zeta streaming potential measured in the ZETA-check, represent the level of electrostatic repulsion between particles. The potential is generated by ionic end groups on particles and macro-molecules, respectively. With ZETA-check, the state of the actual charge of dispersions and macromolecular solutions is obtained within seconds. Solutions and dispersions from 0.3 nm up to 100 µm particle size qualify for measurement.
-
product
Particle Image Analyzer
DRK-7020
Shandong Drick Instruments Co., Ltd.
Determine the melting point to detect the purity of crystal material. Mainly used for determination of medicine, dyestuff, spice, and other crystal organic compounds’ melting point. Using photoelectric automatic detection, dot matrix image liquid crystal-display technology, and digital keyboard input. The instrument can measure three samples at the same time and has the initial melting, final weld automatic display, automatic recording of melting curve, automatically determine the melting point of the mean value function. The temperaturesystem uses highly linear platinum resistance as detection elements and PID regulation technology, improved the melting point’s precision and reliability. The instrument establishes communication with PC through the USB or RS232, printing or saving the curve and it uses capillary Pharmacopoeia as sample tube.
-
product
AEROTRAK™ Handheld Particle Counters
9306
The TSI AEROTRAK™ Handheld Particle Counters offer the most features and flexibility for customers interested in low cost and versatile particle contamination monitoring.
-
product
PXIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PXI FlexRIO Digitizer
785647-01
The PXIe-5774 provides up to 3 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PXIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
Handheld Particle Counters
Models 3888 And 3889
Kanomax’s innovative Handheld Particle Counters (Models 3888 & 3889) set the standard of instrumentation in cleanroom / operating room monitoring and verification, filter testing, IAQ investigation, data center cleaning and many more highly specialized and highly sensitive applications. These beautifully engineered devices boast some of the most highly advanced technology in the industry. A combination of accuracy and practicality, these devices count airborne particles with high quality performance.
-
product
Monodisperse Generators
Specific applications include calibrating particle counters, testing various filters, and studying size-dependent particle properties.
-
product
Aerosol Neutralizer
3054
Aerosol neutralization is an important component of aerosol science and engineering. Neutralizing aerosol particles can reduce electrostatic losses of particles within tubing or to other surfaces. Neutralization is also critical to gathering reliable particle size data when using a sizing instrument based on electrical mobility.
-
product
Microscopy Image Analysis Software
analySIS FIVE
The image analysis software "analySIS FIVE" is designed for users of industrial microscopes compatible with digital cameras for microscopes. Users can select from 5 types depending on their required functions, such as "measurement," "database," "report creation," and "particle analysis."
-
product
Alpha Spectroscopy
Alpha spectroscopy is used to identify and quantify radionuclides based on the alpha particles emitted in the decay process. Similar to Gamma Spectroscopy, energy spectra are generated with high precision detectors and electronics and analyzed with special software. Typically, samples are measured following chemical separation to isolate the radionuclides of concern due to the complexity associated with correcting for these interferences with spectrum analysis software as is common for many Gamma Spectroscopy measurements.
-
product
Particle Analyzers
Teilch Particle Analyzers have proven significant advantages when compared to competitors’ solutions. Innovations in light source, flow control, analog and digital signal processing, components integration and software allow Teilch to provide a state of the art system for precision particle analysis.
-
product
On-board Emissions Measurement System
OBS-ONE PN Unit
The OBS-ONE PN unit is an on-board emissions measurement system for analyzing the solid particle number concentration within the specified particle size range under real-world driving conditions. The unit uses a condensation particle counter which is recommended principle by the Particle Measurement Programme (PMP), one of working groups affiliated with UNECE.The PN unit combines with the GAS unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
-
product
Neutron Detectors
As a neutron has no charge, a neutron detector incorporates a neutron-to-ionisation particle converter.The incident neutrons are captured by the converter material which then produces (detectable) ionising particles by means of a nuclear reaction.Photonis gas-filled detectors are designed to detect thermal neutrons (En < 0.025 eV), so the capture cross-section of the detecting material must be as large as possible for this low energy. We therefore use 235U (580 barn at 20 °C) for our fission chambers, and 10B (3840 barn at 20 °C) for our boron-lined proportional counters.
-
product
Solid Particle Counting System
MEXA-2000SPCS series
The HORIBA MEXA-2000SPCS series measures the number of solid particles from engine exhaust gas in real-time.The series can complete engine/vehicle certification testing in the latest regulations*1, such as Euro 6/VI and China 6/VI,along with R&D testing of engines and particulate filters by direct sampling without dilution.
-
product
PXIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PXI FlexRIO Digitizer
785647-02
The PXIe-5774 provides up to 3 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PXIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
product
Ultraviolet Checker
For magnetic particle testing. Intensity of ultraviolet can be read directly in mw/c directly.
-
product
Air Samplers
Coriolis Air samplers are dedicated to the collect of biological particles in the air which bring new perspectives for the control of airborne contamination thanks to its liquid sample.
-
product
Automatically Differentiate Cyanobacteria
FlowCam® Cyano
Yokogawa Fluid Imaging Technologies, Inc.
Based on proven FlowCam® technology, the new FlowCam Cyano automatically identifies cyanobacteria from other algae and particles in aquatic samples. Using a patent-pending combination of excitation wavelength, phycocyanin fluorescence measurement and image recognition software, the system automates what used to be done manually using microscopy. After differentiating the cyanobacteria form the other algae in the sample, VisualSpreadsheet and Advanced Classifier software can be used to further characterize the specific types of all algae found in the sample.
-
product
Ingress Protection
Ingress Protection testing evaluates the resistance to particle and liquid entry for an enclosed product. After testing has been performed, the product receives an IP rating, based on IEC 60529, according to the achieved resistance to solid particles and liquids.
-
product
On-Site Oil Analyzer
MicroLab 40
MicroLab 40 is designed primarily for fleets operating equipment with hydraulic components or heavy equipment gears and transmissions. This would include off-road mining and construction vehicles as well as over-the-road equipment with hydraulics such as bucket trucks, fire engine ladder trucks or solid waste trucks. The MicroLab 40 is also used in applications for offshore drilling equipment. In addition to the basic oil chemistry and extended elemental analysis provided with the MicroLab 30, the MicroLab 40 model includes a particle counter which provides critical analysis for cleanliness of hydraulic oils and gear oils to determine the health of those oils and mechanical condition of those components.
-
product
Scattered Light Dust Measuring Devices
The reliable way to detect low dust concentrationsLight scattering by dust particles is a measurement principle that allows even very low concentrations of dust to be detected. Depending on the system-specific requirements, either forward scattering or backward scattering can be used in this context. Both measurement principles return stable and reproducible measurement results, regardless of the gas velocity, humidity, or dust particle charges.
-
product
Piezobalance Dust Monitor
3520 Series
The Kanomax Piezobalance Dust Monitor 3521/3522 is a unique respirable aerosol monitor, providing direct mass concentration of particulates using PIEZOBALANCE technology; ideal especially for oil mist monitoring. The Kanomax 3521 is equipped with 4 and 10µm impactors while the 3522 is equipped with a 2.5µm impactor. Unlike conventional dust meters, which count particles, a piezobalance dust meter like the 3521 or 3522 “weighs” mass concentration of particulates. As an air sample enters the system, it travels through the impactor, which captures and removes larger particulates away from the sample. Smaller particulates become electrically charged and deposited on the piezo-crystal. The total mass of the deposited particulates affects the piezo-crystal’s frequency. Since the change in frequency is proportional to the mass of the particulates, the actual weight of the particulates is obtained.
-
product
Computational Fluid Dynamics
CFD
Computational Fluid Dynamics analysis is a value-added service from Teledyne Cormon that predicts pipeline flow and sand particle behavior for specific project scopes, allowing asset integrity teams to understand the optimal placement for erosion and corrosion monitoring probes.
-
product
Magnetic Particle Flaw Inspection System
This model can perform every kinds of magnetic particle flaw inspection in our unit. circular magnetization longitudial magnetization continuous magnetization, residual magnetization threading bar magnetization current induction magnetization, AC magnetization AC demagnetization DC magnetization, DC demagnetization.
-
product
Front and Back Side Topography Defect Detection
LIGHTsEE
High throughputNanometer range vertical sensitivitySimultaneous double side inspectionNanotopography and Topography measurementDetection of Slip lines, particles, Hairline cracks, SOI voids, Comets, EPI defects…Compliant with thin or thick wafers, taiko wafers, highly warped wafers
