Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber
40-850A-514-M50-HI
The 40/42-850A-514-M50-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
product
Reflection/Transmission Test Chamber
CHTR-100
When measure the surface spectral reflectance of all kinds of reflect mirror, metal, plastic and so on or the spectral transmission of glass and plastic, CHTR-100 Reflection/Transmission Test Chamber is mainly used to collect photometric and chroma energy, and then send the tested light signal to spectrometer or reflection and transmission photometer to get the color parameters via optical fiber or photoelectric detector.
-
product
SFP+ Cable, 1m
784076-01
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model … has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Handheld Singlemode Multimode
OTDR X60
Palm OTDR X-60 is a very reliable and good performance OTDR, it can measure the optical fiber length, transmission attenuation of optical fiber, attenuation of splice, and failure location, etc accurately. It is widely used in the maintenance, construction and monitoring of cable line.
-
product
Probes & Flow Cells
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
product
Laser Diode Driver
S-101
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
product
Low Cost Microwave Wideband Electro-absorption DFB Transmitter
MT62 (40KHz~33GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT62 series microwave DML optical transmitter, are able to transmit 33G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 60Gb/s high speed communication system.
-
product
Optical Power Meter
SAT-4E
Shaanxi Aitelong Technology Co., Ltd
SAT-4E optical power meter is an indispensable tool to identify fiber, measure fiber loss, verify continuity, and evaluate transmission performance, widely used in LAN, WAN, CATV, remote optical network, etc.
-
product
Digital (1kV up) H.V. Insulation Testers
7015 IN
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Microprocessor controlled.● 2 Lines x 16 characters, large intelligent LCD module.● 30 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV, 12.5kV, 13kV, 13.5kV, 14kV, 14.5kV, 15kV● AC/DC Voltmeter.● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Current measurement.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Short-circuit current up to 5mA● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : 1~30 minutes.● Calendar.● Indication memory for data storage.● Optical USB to RS-232 data transmission.● Auto-off.● 200 measurement results can be saved in the memory and recalled on the display.
-
product
Optical Talk Set
FTS100
Shanghai Tarluz Telecom Tech Co., LTD
In some rural site, the mobile phone may be out of service range, if conversation between two operators who are laying down an optical cable for optical network needed. in the situation, Tarluz Fiber Talk Set is essential. With the optical talk sets, the two operators can have talk with each other directly via an intact optical fiber. It is easy and reliable. TARLUZ FTS100 handheld optical talk set with dynamic range of 33dB. The high dynamic range ensures the quality of voice and long transmission distance.
-
product
Microwave Wideband Direct Modulated DFB Transmitters
MT52 (40KHz~20GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT52 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
product
Field-installation Type Dissolved Oxygen Meter (Four-Wire Transmission, Optical Type)
HD-200FL
Optical dissolved oxygen sensor with no electrolyte replacement and rugged membrane.Highly intelligent, including automatic recognition of membrane properties when replacing the sensor cap.The HD-200FL is an optical (fluorescent) dissolved oxygen meter suitable for monitoring aeration tanks used for sewage treatment, effluent treatment, and other processes. Compared to conventional membrane polarographic type sensors, there is no need for electrolyte (internal fluid) replacement or warming, up. Characteristics of optical sensors are utilized to realize unequaled, improvement in ease of maintenance and reduction in running costs. Moreover, it features enhanced user-friendliness, with sensor caps that have built-in memory and a membrane replacement notification function.
-
product
Outdoor AGC Optical Node
SR812
Hangzhou Softel Optic Co., Ltd.
Based on plenty of experience about CATV HFC network optical fiber transmission equipment, we developed SR812, SR812B, SR814, SR814B series field optical receiver which is two-way optical receiver; They are mainly used in long-distance optical fiber transmission of TV image signal, digital TV signal, telephone voice signal and data (or compressed data) signal. We are innovating the product technology, rebuilding the line structure and Improving the process quality since we developed the first CATV optical receiver successfully in 1995; The current WR series optical receiver are not only of the lead position in domestic level regarding line technique, but also the same as imported product regarding technological quality; We have developed a variety of different models for users to choose models.
-
product
1208/9a Optical Distribution, RX/TX
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
product
Entry Level Loss Tester
Model：OLT-20
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
product
40Gb/s DPSK Receivers
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
product
TS Stream Optical Transceiver
OD2000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD2000 digital fiber transmission system is designed and produced specially for long transmission and network construction of DVB DTV TS stream. OD2000 can modulate the MTS program signal (coming from the 1~8 ways separate multiplexer at the head-end generator room) to FMTS optical signal high-speed code stream. It is an important device to transmit TS stream between DTV head-ends.
-
product
Microspectrophotometer
MSP Series
Angstrom Sun Technologies, Inc.
Microspectrophotometer (MSP) is an advanced optical system. The key difference with typical low cost reflectometer is in its capability to characterize optical properties of thin films over a micron region area. With unique design by Angstrom's professionals, user can enjoy digital imaging capability in Microspectrophotometers (MSP series) by live video, powerful digital editing, measurement tools for reflection, transmission, absorption spectra. Data acquisition only takes milliseconds.
-
product
DCA-X Sampling Oscilloscopes
The DCA-X wide-bandwidth sampling oscilloscopes are in our digital communication analyzer (DCA) family. These are modular platforms that provide accurate and precise measurements of high-speed digital designs from 50 Mb/s to 224 Gb/s. You can configure the DCA-X mainframes by selecting from a variety of plug-in modules that perform precision optical, electrical, and time domain reflection / transmission (TDR / TDT) measurements. Select specific modules to obtain the desired bandwidth, filtering, and sensitivity that match your measurement needs.
-
product
Gesture, Color Sensors & Proximity Detection
The gesture product family performs advanced gesture detection, proximity detection, digital Ambient Light Sensing (ALS) and color sensing (red, green, blue and clear). It also implements optical pattern generation for barcode transmission and remote controls. The gesture sensor modules provide a highly integrated solution offering five essential functions to enable a touchless interface and to optimize the end user experience of communications and consumer electronics equipment. Gesture detection uses four directional photodiodes to sense IR energy emitted from the integrated LED, converting the measurements of reflected IR light into information about physical
-
product
Optical Filter Sets
Our filter sets support a great range of fluorophores for microscopes and imaging systems. Patented design techniques drive some of the most spectrally sophisticated optical filters on the market. High transmission, steep edges, precise spectral edge placement, and optimized blocking combine for more reliable measurements. A wide selection of individual bandpass filters and dichroic beam-splitters support unique applications, and world-class manufacturing and cutting-edge metrology ensure consistent performance that always meets specifications.
-
product
Triple IC Optic Node
OX 733
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Tecnology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -13 dBm Sensitivity- RF O/P at 0 dBm : 113 dBµV
-
product
Digital Portable Panel Meters
ST-2001 ACV
Standard Electric Works Co., Ltd
● Big-size LCD (112 x 59mm)● Backlight function.● Analog scale with Bar-graph for viewing. (100 bars)● 10000 counts (high resolution).● DCV Ranges: 99.99mV~999.9V (ST-2001 DCV). ● ACV Ranges: 99.99mV~800.0V (ST-2001 ACV). ● 5 manual ranges controlled by rotary switch.● Data Hold function● Low battery indication● 9V power supply● Best resolution of 0.01mV (10uV)● Precision meter for factory maintenance, field servicing and educational purposes.● With an optical USB to RS-232 data transmission cable. (DCV-R & ACV-R)● 2 optical LEDs are built-in for data transfer. (DCV-R & ACV-R)● Well isolated to contact. (DCV-R & ACV-R)● The software is included (Compact disc). (DCV-R & ACV-R)
-
product
Optical Protection System ( Single Fiber Two-Way )
OPS-1000
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
-
product
Transmission Hazemeter
Novo-Haze TX
The Novo-Haze TX Transmission Hazemeter offers fast and accurate measurement of the optical quality of plastic films and other transparent materials. This instrument measures total transmission and haze according to ASTM D1003 (CIE C), the most important standard used in most QA applications.
-
product
NIR & UV-VIS Process and Lab Analyzers
The optical or spectrum analyzer is the brain which transforms the signal collected by the sample interface into actionable information. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV-Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal light transmission for long-term reliable measurements. More information is available about specific analyzers on each product page or on the process analyzer product overview.
-
product
Fiber Amplifier - Node With Supply
FANS 811-812
- AGC - Automatic Gain Control- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lasers with Isolators- Variable SLOPE/GAIN Control- Input Wavelength : 1310/1550nm- Output Wavelength : 1310nm- Digital Display of Optical Level- External FusesPower Options :- Mains 220VAC, 50Hz- 12V DC / 2 Amp- 40VDC from “40V/RF out” connectors
-
product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
product
(70×90×15mm) Full Function Single Channel MSA Compact Pre-Amplifier EDFA Module
SPA4300-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-FM02 is a full-function optical Pre-Amplifier with digital control electronics, adopts 70×90×15mm MSA compact package. It is featured with high reliability, superior optical performance and compact reasonable configuration by Industrial standard, creating the most flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
