Filter Results By:
Products
Applications
Manufacturers
-
product
Binary BCD Converters
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
product
UV Nanosecond Lasers
355 nm wavelengthPower: 0.5W* to 5W*Air-cooled design, water cooled optionAll-in-one (AIO) single box design for 0.5 & 1W modelPatented intracavity UV generationCompact, rugged, monolithic laser headTotal pulse controlTEM00 beam with typical M² < 1.2Pulse rates from 1Hz to 300kHzRS232 computer controlField replaceable pump diodes
-
product
- RS-232 DB9 Lightning Suppressor
Model 29
FEATURES: PC 386/486 Pentium Com Ports; Nanosecond Response; DB9 Connectors; Protects All 9 Lines; Ground Stud & Wire Included. The Model 29 contains avalanche diodes, one for each line. All diodes are returned to a ground stud. The Model 29 is provided with a 2-foot ground wire and has male and female DB9 connectors.
-
product
Pulse & Delay Generators
The benchtop pulse generators feature a fast risetime and low jitter. Our most popular digital delay pulse series 575 and 577 generators are now available with selectable time references. With up to eight channels of delay and width control, each individual channel's reference can be set either to the trigger or to any other channel. So look below if you require a picosecond pulse generator or nanosecond pulse generator for your application.
-
product
Pulsed X-ray technology
Golden Engineering X-ray generators are based on Pulsed X-ray technology. Pulsed X-rays generate a high intensity X-ray burst (pulse) in a very short period of time (10 to 50 nanoseconds depending on the model). The output dose of each pulse is 3-6 mR measured 12 inches from the front of the X-ray generator. The operator varies the overall dose of each exposure by changing the pulse setting. The pulse rate varies from 10 pulses per second to 25 pulses per second depending on the model. The generators can fire up to 200 pulses before a four-minute rest period.
-
product
High Current / High Voltage Pulsers
DEI Division
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
product
GPS Master Clock
Signals & Systems India Private Limited
GPS Master Clock System – MCS-GPSMC-1010 is a 3U Card rack type, 19” Rack-mountable Redundant GPS Time Server which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from any one of the sources like GPS or GLONASS or Time protocols such as NTP and IRIG. It distributing the same time signal through several types of interfaces. It provides redundancy for Power and GPS receiver to increase reliability and offers protection against time synchronization failure. The system is field-upgradeable and an extremely flexible system, designed to handle time synchronization requirements today and in the future. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, DCF77, BCD parallel data, Ethernet Fiber Optic & RS485/RS232 outputs. System enables configuration and monitoring through Web-based application. It supports a wide range of power supply either 90V-260V AC/DC or 18-36VDC or 36V-72VDC. Power supply model can be mixed and matched as required by the user, depending upon power supply options available at the installation site.
-
product
Interface
R15-EC
The R15-EC card provides the highest level of performance and density for MIL-STD-1553A/B in an ExpressCard form factor. The R15-EC card provides 1 or 2 channels integrated with powerful API software that provides instant access to all 1553 databus functionality and data. Standard features include real-time bus playback (with ability to edit out RTs), aperiodic message insertion, error injection/detection, conditional BC branching, 64-bit, 25 nanosecond message timetagging, and “Oneshot” BC operation. The Bus Monitor mode provides 100% bus monitoring of a fully loaded 1553 bus. IRIG-B Receiver (AM or DC/TTL) Generator (DC/TTL) optionally available.
-
product
Switched Filter Banks
Switched Filter Banks typically include multiple filter topologies, including PIN diode and MMIC switch sub-circuits to achieve operational bandwidths of greater than 3 octaves. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds. GaAs MMIC Based Switched Filter Banks provide switching times as low as 10 nanoseconds with very low power consumption and have the inherent advantage of supporting multi-octave frequency bands with extremely low power consumption.
-
product
Single Photon Detector System For Near-Infrared (0.7 - 2.3 Um Wavelength)
*Frequency range includes coverage into higher frequencies than other photon counters on the market.*Short dead time (10 nanoseconds) compared to long dead time (microseconds) of alternatives. Therefore rapid repeition rate of 10s of MHz possible, whereas alternative have maximimum repetition rate of 1-10 kHz.*Very small dark counts (10/second) compared to high dark count (1,000s / second) of alternatives. Does not require gated mode unlike alternatives. Operates in continuous operation mode.
-
product
High Level of Customization at an Affordable Price
TLP
The Impulse transmission line pulser (TLP) discharge networks are easily integrated with other instruments for a custom system matched for your device and process applications. Specifications include 1-10 nanosecond rise times, up to 40 amps peak, for 10-500 nanosecond pulse widths. It is a proven design incorporating 15 years of hardware and device development experience. Reliable performance over hundreds of processes, and thousands of products. All TLP systems are built by special request, contact us with your specifications or application.
-
product
Digital Delay Generators
Highland has introduced three unique features to digital delay generation: a "Queued Updates" feature allows time settings to be changed without corrupting ongoing timings; a "Train" feature allows multiple pulses to be generated from each trigger; and a "Frames" feature allows complex delay sweeps and pulse scenarios to be pre-loaded and rapidly executed. Digital delay and pulse generators are available in 1-6 channels, with square, Gaussian, and arbitrary waveshapes, and insertion delays as low as 10 nanoseconds.
-
product
Diode Laser Driver
D200
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
product
Camera Link Frame grabber
Cyton-CXP
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
product
Intermittent Fault Detection & Isolation System
IFDIS
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
product
Flashlamp Pumped Actively Q-switched Lasers
NL300 Series
NL300 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 800 mJ per pulse at 1064 nm. A wide range of harmonic generator modules for generation up to a 5th harmonic (213 nm) is available. The NL300 series nanosecond lasers are an excellent choice for many applications, including laser ablation and marking, OPO pumping and other critical tasks.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
product
GPS Time Synchronization Unit
Signals & Systems India Private Limited
GPS Time Server – GPS-DRM-1010 is a compact DIN rail mountable unit that synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from different external sources such as GPS and GLONASS. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through a Web-based application.
-
product
Radar Level Gauge
HRRD730 Series
HighReach Measuring & Controlling System Co.,Ltd
At The Radar Level gauge Antenna emits and Narrows at The Microwave Pulse. This Pulse propagates in Space AT at The Speed of Light. The When IT Encounters at The Surface of at The the Measured Medium, Part of the ITS Energy IS the REFLECTED the Back and Received by at The Same, Antenna. At The Time interval The Between the transmitted pulse and the received pulse is proportional to the distance from the antenna to the surface of the measured medium.Because the electromagnetic wave propagation speed is extremely high, the time interval between the transmitted pulse and the received pulse is very small (on the order of nanoseconds). It is difficult to confirm. The 90X series 26G radar level gauge uses a special demodulation technology To accurately identify the transmitted pulse and the time interval of the pulse is received to further calculate the distance of the antenna from the surface of the measured medium.
-
product
DFM (Deep and Fast Modulated) generators up to 280 GHz
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
product
Intensified Cameras - Ultra-Sensitive CMOS Cameras from Deep UV to NIR Spectrum
iCameras
The cameras are equipped with a high-resolution sensor with high frame rate for excellent quality of image production, which is well‐suited to detect high speed moving objects or ultra-fast phenomenon.The mechanical architecture of the iCamera is small, compact and light-weight, especially designed for easy integration into any system.The iCamera features an exceptional sensitivity based on high QE image intensifier - ultra-fast gating technology down to a few nanoseconds, which allows it to be coupled with a laser source to perform high fidelity active imaging.
-
product
Shunts
WSM alternating current measuring resistors have compared with traditional direct current shunt resistors with coaxial voltage tap significantly better high-frequency transmission characteristics. This resulted from a production engineering very complicated structural design of the active part.ISM pulse current measuring resistors allow the metrological recording of the time curve fast current changes large amplitude in the nanosecond range. The ISM are designed for the pulse current measurement with broadband oscilloscopes.
-
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
SEM- Based Dectors
ScintiFast™
ScintiFast™ is El-Mul’s flagship scintillator technology enabling the next generation of detectors with shorter response time and higher sensitivity. Recently released, ScintFast™ has the highest available photon yield for the nanosecond scintillator category. ScintiFast™ is the scintillator of choice for detectors in SEM-based tools for the semiconductor market as well as in Time of Flight Mass Spectrometry instruments.
-
product
Hawk - E Co Processor
9322 E
Basic Hawk Co-Processor card set with 2.0 Mbyte memory and microcoded instructions for Nova 4X and Eclipse S280. Executes ALU instructions in 275 nanoseconds. ISA bus compatible, two slots required. Approximate CPU performance of actual S280.
-
product
Nanosecond Pulsed Lasers
Our nanosecond pulsed lasers feature pulses in the ns range. For picosecond and femtosecond lasers please see Ultrafast Lasers.
-
product
SPDT PIN Diode Switches
Fairview offers a comprehensive selection of 23 different models of SPDT PIN diode switches that cover frequencies ranging from 10 MHz to 67 GHz. The high isolation levels up to 80 dB ensure that unwanted signals will not leak into the desired signal path. Other critical performance features include low insertion loss as low as 1.1 dB and fast switching speed performance as low as 50 nanoseconds. Both absorptive and reflective designs are available and every model utilizes integrated TTL compatible high speed driver logic circuitry. These SPDT switches are constructed using MIL-Grade rugged coaxial packages and several models support field replaceable connectors. All models are EAR99.
