Filter Results By:
Products
Applications
Manufacturers
Low Pass Filters
Refine signal, allowing the transmission of signal below a specific corner frequency, while attenuating the frequencies above.
See Also: Filters, Filter / Amplifiers, EMI Filters, Programmable Filters
- Pickering Interfaces Inc.
product
LXI Low Thermal EMF Matrix 1-pole 42x33
60-510-002
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
1.3GHz Frequency Counter
Model 1122 / 1122X
- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)
-
product
Lowpass Filters
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Spectrum Marker Generator
NSG-2
National RF, Inc. is pleased to announce the production of a new device, the Type NSG-2 Spectrum Marker Generator. The generator is intended to be used with either spectrum analyzers or communications receivers to mark specific frequency intervals in the RF spectrum. When used with receivers, it is essentially a frequency calibrator, thus making it attractive for use with vintage receivers with analog dials. The NSG-2 provides a leveled amplitude output over nearly 100 MHz of RF spectrum, thus making it ideal to mark frequencies and signal levels on spectrum analyzers. In addition, it may be used with a spectrum analyzer, in lieu of a sweeping type generator, to align lowpass, highpass, and bandpass filters with passbands greater than 20 KHz.
-
product
Precision Dual-Channel Compact Filter/ Amplifier System
PFA-2
he PFA-2 is a compact, rugged, and versatile dual-channel precision filter/amplifier. The low-noise, high common-mode rejection balanced differential input with programmable AC/DC input coupling is ideal for conditioning static or dynamic signal inputs. Sharp, programmable 6-pole low-pass precision filters support two response characteristics which are optimized for making time-domain or frequency-domain measurements.
-
product
Active Filter
J2190A
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
product
16-Channel Anti-Alias Low-Pass Filter Card
AAF-16
The AAF-16 is a 16-channel anti-alias low-pass filter card series for front-end signal conditioning in PC-based data acquisition systems.
-
product
Precision Analog Anti-Alias Low-Pass Filter Board
GSAF-10
The GSAF-10 Gold Series are analog low-pass filter boards that offer the performance required to maintain the maximum accuracy of high-precision 16- and 18-bit A/D converters.
-
product
0.1Hz-3.7GHz Frequency Counter
FC-3000
Features:*Frequency measuring range: 0.1Hz to 100MHz in A input, 80 MHz to 3.0GHz in C input.*Period,Total and RPM measurement for input A*9 Digit display with 0.01mHz resolution in 1 Sec (By Ext.Reference signal).*RS-232C serial interface function for communication with computer.*High sensitivity Extemal reference input function(>=1.5Vrms).*Peciprocal technique for high resolution at low counting frequencies .*Self check function executed to perform a automatic self diagnosis of various counter function.*Push-scanning for selecting Function and Gate time.*Low-pass filter(100KHz,-3dB)installed for removing noise signsl in low frequency measuring.*AC/DC coupling function(Selectable AC/CD Coupling)*10:1 Input Attenuation(Selectable×1/×10 Attenuator)*Data hold function
-
product
Filter Building Blocks
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
product
Loggers/PQA
Kyoritsu Electrical Instruments Works, Ltd.
Large capacity for storing 60,000 data points Lowpass Filter will filter out the harmonics LED flickers when the preset current/voltage value is exceeded CALL:Confirmation of recorded data Selection of One-time mode or Endless mode Non Volatile Memory Battery power indicator The userfriendly PC software "KEW LOG Soft 2" is supplied Continuous measuring time:Approx. 10 days (Alkaline Battery)
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Tunable Edge Filters
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
product
Lowpass Filters
K&L Microwave provides lowpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
product
Low Noise Dual Band VCO
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
product
ACDC
EC Series
The EC Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
100GHz Optical Add/Drop Multiplexer
OADM-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1000 100GHz optical add/drop multiplexer based on the mature thin-film filter technology, metal seal. With so much great features like low insertion loss, high isolation, wide pass band, flexible configuration and so on. This is the ideal parts for used in DWDM system Add/Drop special wavelength.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-819
The SCS-818 and SCS-819 amplifier/filter module provides eight 4-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-818) and 0.5Hz to 70kHz(SCS-819). Each of the SCS-818/SCS-819's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Dual Voltage Buffer with Current Drive
BUF-01
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-2Fe
Programmable, 2-Channel Low-Pass Filter Module. The AAF-2Fe may be used with the AAF-3PCI, AAF-3, AAF-2, or AAF-1 filter boards.
-
product
Clamp Meters
0.001 mA Current Resolution, Comply With IEC61557-13: Class 2, ≦ 30A/m, True RMS Measurement For All Applications, Low Pass Filter Function
-
product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
product
EMI/EMP Connectors
Filter connector series includes EMI/ EMP/ESD circular, ARINC, D-subminiature and micro-D connector styles. They can be combined with high energy TVS diode technology to achieve lightning and EMP transient protection. Smiths Interconnect's EMI filter connectors use multi-layer ceramic capacitor arrays together with inductive materials to realize robust, high performance low pass filter networks. Where required, transient protection can be combined with EMI /RFI filtering to provide maximum protection. The diodes as well as the EMI filter are packaged separately so the construction of the connector remains modular.
-
product
Passive Components
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
