Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
product
Filters
ZF
Antenna Technology Communications, Inc.
ATCi offers a selection of filters designed to reject out-of-band interference.
-
product
Wi-Fi signal analysers
An advanced Wi-Fi analyser is essential to avoid channel interferences in large public or corporate wireless networks.
-
product
VLF Diagnostics System
PHG 70 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
product
Hystograph
HG 200
Dr. Brockhaus Messtechnik GmbH & Co. KG
This process runs with constant flux alteration d/dt and avoids interference caused by eddy currents and phase displacement between the field strength and polarization measurements.
-
product
Terahertz Spectroscopic Analysis System
TAS7500SL
Research in the area of materials for terahertz wireless communications, etc. 0.03-2THz frequency range is optimized for research in the area of materials for terahertz wireless communications, etc. Easy module switching requires no adjustments Attached dry air unit eliminates moisture interference
-
product
PXI Waveform Digitizer
PXD731x/70xx
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
-
product
Shallow TEM Magnetic System
WTEM-2Q
WTEM-2Q time domain shallow TEM system is one of our latest researchers, with all functions and advantages of domestic and oversea shallow transient electromagnetic survey systems, integrated with WTEM-1J/GPS TEM system receiver and WTEM-1X low-power transmitter. It features high transmitting power, short turn-off time, high reliability, strong anti-interference performance (atmospherics, 50Hz or 60Hz industrial frequency interference), lightweight and low power consumption.
-
product
Modulation Distortion Up To And Beyond 125 GHz
S930713B
S930713B enables fast and accurate active-device modulation distortion characterization under modulated stimulus conditions up to and beyond 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930713B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
IC EMC Analysis
We carry out standard measurements according to BISS/IEC and analysis of the interference immunity and interference emissions of ICs during development.With the targeted EMC analysis, we uncover weak points in the ICs so that the IC developer can use them to develop improvements for the product
-
product
Heat Flux Sensors
MF Series
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
-
product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
product
SGMA RF Source
SGS100A
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
product
EMI Filters And Application-Specific Integrated Products (ASIP)
An electromagnetic interference (EMI) filter is used in electronic circuits to improve system immunity against unwanted external electromagnetic signals from neighboring circuits and to avoid emitting radiation (“noise”) that may disturb the same nearby circuits by canceling unwanted frequencies.
-
product
H.V. Multifuntion Phasing Sticks
PC7k, PC11k, PC22k, PC33k, PC44k
Standard Electric Works Co., Ltd
● No user’s assembled parts.● Dual color-coded scale (%, Vac).● Neon indicator when >1200Vac.● Lightweight, robust & compact.● Carry case included.● Compare between phases.● Measure and test phase to earth.● High quality fiberglass wound rod.● Self powered operation. No battery required.● DC version available.● Measure phase to phase.● Hi immunity to interference fields.● Suitable for indoor and outdoor use.● Current is limited to ±1 milli-ampere.● Grounded or ungrounded systems.● Meets IEC 61481 (excludes PC44K).
-
product
Dynamic Frequency Selection
MET is a leader in performing DFS testing on a variety of WLAN products for FCC, ISED, EU and Japan requirements.Many countries require wireless devices operating in unlicensed 5 GHz bands to have the capability to detect interference with other technology sharing the spectrum (such as military and weather radar systems) and automatically switch over to another frequency.
-
product
Flash SATA Disk/mSATA Mini SATA 3 SLC, MLC
FSA 301 Series
*SATA III (6.0Gb/s) interface*Capacity: SLC 1 GB to 32 GB, MLC 4 GB to 64 GB*iSMART disk health monitoring*Intelligent error recovery system*Write protection security*Anti-vibration mechanical design*Excellent data transfer speed*Zero mechanical interference*JEDEC standard MO300B dimension
-
product
Digital Teslameters/Gaussmeters
S Digital Teslameters offer accurate, high resolution measurement of magnetic flux densities, withdirect digital readout in tesla or gauss, and serialcommunications by fiber optics or RS-232C for system applications.The instruments are light and compact, and the probes are easy to use. The DTM-151 has been engineered to withstandthe severe electrical interference produced by high voltage discharge.
-
product
Insulation Resistance Meter
AMIC-15k1
*The partial discharge indicator PDI.*Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD*Allows to test the electrical durability of the tested object - indication of breaking voltage.*The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
product
VLF Diagnostics System
PHG 80 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 80 TD. The combination of the PHG 80 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
product
HDMI Over Fiber Transmitter and Reciever
QuestTel''''s HDMI Transmitter and Reciever singlemode extender over fiber optic cable integrates HDbitT technology in one standalone kit, it allows you to transport HDMI 4KX2K - 25/30Hz signal up to 20km from the source device to destination display using SC connectors.This HDMI extender supports IR back transmission function. It features with low signal loss and tolerance for electromagnetic interference.
-
product
1208/9a Optical Distribution, RX/TX
Precise Time and Frequency, Inc.
The ptf 1208A (transmitter) and ptf 1209A (receiver) provide a convenient and simple way to transmit high quality RF signals over long distances, without the concerns associated with electrical interference and pick-up.The ptf 1208A accepts an RF input in the range from 1kHz up to greater than 10MHz and provides a combination of 8 local, high isolation, RF distribution outputs and 4 optical transmission outputs for distances up to 2 kilometers.The ptf 1209A accepts an optical input (transmitted from the ptf 1208A) and provides 12 local RF outputs, either digital (TTL into 50 ohms) or low noise sine wave signals driving 1V rms into 50 ohms (with the PLL option), or both.These systems are especially designed to accommodate IRIG B DCLS, 1PPS and other RF signals in the range from 1kHz to 20MHz.The modular construction allows for a variety of input/output configurations to provide a fully tailored application solution.
-
product
EMF Measurements/EM Measurements/Electromagnetic Radiation
Holland Shielding Systems B.V.
Electromagnetic fields cause interference in electronic devices and may affect the health of people close to where the fields are generated. It is important to recognize this at an early stage in a construction process, for instance at a future construction location or while construction is already underway, so that budgets are not exceeded. By means of field-strength measurements one can chart the existing electromagnetic fields and radiation emitted by GSM, UMTS antennas and transformer spaces, to mention a few examples. These measurements can help determine the best location in the new building for rooms where sensitive measurements are to take place, e.g. in hospitals or nano laboratories. And last but not least, field-strength measurements can detect sources of interference and can be part of a scheduled check of existing screened spaces and Faraday cages.
-
product
Superconducting QUantum Interference Device (SQUID) Magnetometer
Quantum Design MPMS®3
Quantum Design's MPMS 3 represents the culmination of 40 years of development and design in the world of SQUID Magnetometry. Providing users with the sensitivity of a SQUID (Superconducting QUantum Interference Device) magnetometer and the choice of multiple measurement modes, the MPMS 3 offers new levels of performance in magnetic research while including those aspects of past Quantum Design SQUID magnetometers that customers have grown to appreciate and depend on.
-
product
Domestic Direct Reading Spectrometer
CS-8610
Wuxi Tianmu Instrument Technology Co., Ltd.
1. Convenient, practical and reliable: unique combustion device, equipped with infrared detection system, direct connection, remote control operation.2 , patented burner design (using utility model patent technology)The burner electrode upgrading system adopts a spring structure, the electrode adjustment is convenient, and the double sealing ring guarantee the pressure balance in the furnace cavity without tempering.3 , to ensure accurate measurement results◆Using low-noise, high-sensitivity, high-stability pyroelectric infrared detectors.◆Specially-made new platinum infrared light source, continuous heating and high spectral efficiency.The modular design of the whole machine, the electronic circuit is highly integrated, which improves the reliability of the instrument.◆Industrial-grade integrated linear module power supply, stable output, no fault.◆The infrared detection part and the combustion furnace are connected by optical fiber, and cooperate with multi-level concealed isolation circuit to completely eliminate arc interference.◆Double filter device to reduce the impact of dust on the analysis results.4 , electronic balance is not quantitative sample: you can choose different brands of electronic balance, automatic online, to achieve non-quantitative weighing.
-
product
Measurement Technology for the Development Stage
EMC tools for relative measurements of interference emission of assemblies and devices.
-
product
Acoustic Emission Preamplifier
The Acoustic Emission Preamplifier is a instrument designed specifically for use with acoustic emission sensors, which is used to boost the signals and filter out any noise or interference. With its advanced technical features and robust design, the QingCheng Acoustic Emission Preamplifier is the perfect choice for professionals seeking a high-performance acoustic testing solution.
-
product
Inductively Coupled Plasma Mass Spectrometry / ICP-MS Systems
Agilent ICP-MS systems utilize innovative technology to deliver excellent sensitivity, accuracy, ease of use and productivity. Our 7800 and 7900 quadrupole ICP-MS systems offer the highest matrix tolerance, widest dynamic range and most effective interference removal for trace elements across most typical applications. The 8900 Triple Quadrupole ICP-MS (ICP-QQQ) adds MS/MS operation, providing precise control of reaction cell processes to ensure the most consistent and accurate results, resolving interferences that are beyond the capability of quadrupole and sector-field high resolution ICP-MS.
-
product
Data Acquisition & Signal Conditioners
Electro Standards Laboratories
Electro Standards Laboratories offers instrumentation and signal processors in both encased form factors or board-only versions suitable for embedded sensor applications. Features ability to collocate with sensor and provide immediate digitization and signal processing in order to minimize ambient interference on sensitive sensors and to seamlessly integrate into networked sensor architectures.
-
product
Levitator
The ultrasonic levitator is ideally suited for a large number of material science experiments in which small samples or sample quantities have to be positioned precisely. Measurements can be conducted – as they are performed in a touchless manner – without interference from a contact surface.
-
product
Alpha Spectroscopy
Alpha spectroscopy is used to identify and quantify radionuclides based on the alpha particles emitted in the decay process. Similar to Gamma Spectroscopy, energy spectra are generated with high precision detectors and electronics and analyzed with special software. Typically, samples are measured following chemical separation to isolate the radionuclides of concern due to the complexity associated with correcting for these interferences with spectrum analysis software as is common for many Gamma Spectroscopy measurements.
