Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Docking / ATE
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Floating bushings allow up to .04" of re-alignment. Use with a combination of various I/O modules and a max of 5,952 signal contacts simultaneously. The iDock series is rated up to 100,000 cycles.
-
product
In-Line / Board Handler
Circuit Check’s in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading ICT handlers including Keysight 5i, Teradyne TSh Multi-Site, IPTE and Pematech. Circuit Check is the go-to partner for in-line functional test fixtures to speed production throughput.
-
product
SlipFinder
YIS and SF Series
The YIS and SF Series metrology systems are designed for optical detection of wafer defects such as crystaldislocations, slip and other defects. The YIS-300HM (for 300 mm wafers) and YIS-200HM (for 200 mm wafers) utilizeMakyoh optics technology (Magic Mirror) and integrated robotic wafer handler provided by Hologenix.The SF300M and SF300N systems offer a low cost functionally equivalent alternative to the YIS series.
-
product
Prototype Engineering Test
PET-2/PET-3
Exatron's Prototype Engineering Test (PET) Fixture is a semi-automated solution that bridges the gap between a fully automated handling system and a low cost, lower volume handler.
-
product
Milliohm Meter
16502
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluation4 channels R scan with balance check function for fan motor (combined with A165017 option)0.001mΩ~1.9999MΩ wide measurement range with 4½ digits resolutionStandard RS-232 interfaceOptional GPIB & Handler interfaceBin-sorting functionComparator and pass/fail alarming beeper functionLarge LCD display (240 x 64 dot-matrix)Friendly user interface
-
product
Tri-Temp Octal Sites Handler
3160-C
Chroma 3160-C is a productive pick & place system for high volume multi-site IC testing.
-
product
Digital Low Resistance Tester
TH2512
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
product
Programmable Low-Ohm Meter
DU5210/5211
Delta United Instrument Co., Ltd.
20m ~ 2Mtest range, 0.1% accuracy Provided Level and Pulse measurement modes, can be lower temperature influence in Pulse Mode Provided HI/LOW limit and BIN Sorting comparator function, to meet your needed 100 sets of memory, can be saved test parameter and comparator setting, easy to use. Auto Calibration Program Function, to easier your calibration procedure. (Specificity calibrator needed) Cover up free, system firmware upgrade can be update via RS-232, easy to maintenance High speed FADC, max. test speed up to 80 meas./sec, faster your automation equipment 240*64 Graphic LCD display, can be read the reading clearly and easier. User friendly programmable interface, easy to use Provided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
High Performance Strip Handler
Rasco Jaguar
Jaguar is designed for high-volume production testing of ICs on a strip format or in device carrier. It is fully automotive qualified for tri-temperature test and the ideal solution for high parallel testing of small packages at short test times, but also for Power and Sensor devices. Due to the integrated vision alignment and high precision linear motors, Jaguar provides high yield and excellent OEE.
-
product
Striptest Contactors
ULTRA® CONTACT Series
ULTRA® CONTACT Series offers high yield, durability and consistent performance under the most demanding testing environment. Our design offers easy integration to most test handler platforms and on automotive devices.
-
product
Test House Services
Microtest provides complete test house services in a clear room equipped with the state of the art handler and wafer probing system using its own innovative ATE.The test house operates in hot, cold and room temperature for both production and characterization test.Innovative reliability system for Burn In and HTOL ServicesStatistical analysis is performed for digital and mixed-signal devices.Microtest Pacific Test house is located in Malacca (Malaysia).
-
product
Pick And Place Contactors
Designs available for all Pick and Place handler brands, suitable for all range of packages with Multiple Pitch and various numbers of I/Os. Full tri-temp capability up to 180 Deg C.
-
product
Programmable LCR Meter
DU-6211
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 75 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
High-Speed Laser Mark Handler
MCT MH-3300
MH-3300™ high-speed laser mark handler is used for marking of 2DID codes on the lead frame in support of strip testing, marking of reject devices, and for final package marking in strip test or assembly operations. The MH-3300 offers unparalleled throughput performance and the best cost-of-ownership in the industry.
-
product
Component Test Systems
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
product
LCR Digital Bridge
FD2810B
• Test parameter: C, R, L, Z, D, Q• Test frequency: 100Hz, 120Hz, 1kHz, 10kHz• Test level range: 0.1V, 0.3V, 1.0V• Output impedance: 30Ω, 100Ω• Slow or fast (15 times/s)• Automatic selecting, out of limit alarming• Provide the RS-232 & HANDLER interface• Accuracy: 0.1%
-
product
Capacitor Leakage Current Meter
DU2316/2317
Delta United Instrument Co., Ltd.
Leackage Current range display: 0.0001uA ~ 20.00mAAutomatic or Manual trigger with CHARGE/TEST/DISCHARGE100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceHi / Lo current limit setting & PASS/FAIL judgment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Miniature IC Handler
3270
Chroma 3620 is an innovative system handler for high-volume multi-site IC testing, especially for CIS Testing, at the system level.
-
product
Tabletop Single Site Test Handler
3111
The Chroma 3111 is an automated pick & place handling system ideal for small lot engineering samples and/or NPI test development parts.
-
product
Automated Fiber Handler
1200
The 1200 Automated Fiber Handler is the first fiber preparation product that enables optical fiber manufacturers to significantly reduce the cost of production measurements by automating the critical optical fiber stripping, cleaning, cleaving and temporary coupling processes.
-
product
Automated Lead Frame Testing
Sigma MAG
The Sigma MAG comes with an independent lead frame (un)loader for hands-free bond testing. The magazine handler is compatible with OHT and AGV and allows top and front-loading of multiple types
-
product
Package Test Loadboards/DIB
DTS Package Test (DIB) loadboards are designed to specific devices and configured for both hand test and fully automated handler applications. DTS loadboards incorporate any brand of socket or contactor and can be configured for multi-site testing. Designs incorporate all necessary components, connectors, mechanical hardware and stiffeners to provide a complete plug-n-play solution. DTS has a vast database of tester and handler information which allow designs to be started and completed quickly without burdening the customer to supply excessive information. DTS designers are experienced in all device types, including digital, analog, mixed signal and RF devices.
-
product
Test Handler
JOT M5
Simple, cost-effective way to automate PCB and pallet based testingSafe, reliable product handlingQuick-adjust ease: no product-specific partsFaster handling of smart productsIndustry 4.0 autonomous interconnectivityTruly scalable for growing test needsReusable, application-specific test boxesM-TestBoxes compatible with M1 handlerBoxes are fully independent, just pull out from M5 rack and use in off-line testingFail product separation to integrated magazineSpacious service-friendly constructionErgonomic workspaceTouchscreen UI with base statistics and service capabilityEasy start-stop operabilityAutomated width adjustment
-
product
High Speed Pick and Place Handler
Commander 2000
At throughput rates in excess of 2000 Units per Hour the HT Commander 2000 system provides unparalleled performance for the production handling and programming of flash memory devices or modules.
-
product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
product
Turret Test And Scan Handlers
Turret platforms for semiconductor test, inspection and packaging.
-
product
Film Frame Test Handler
4170-IH
High throughput ・High withstand load, and high thrust table ・Expansion of the strip attachment area ：260(L) X 300(W) [Withinφ300mm for WLCSP]・LOT control by barcode/2D code reader ・Easy device type exchange only test socket and display screen setting・Auto-cleaning function unit is installed to clean the socket at any desired timing.・8/12 inches ring conversion ・S2/S8 regulation compliance・SEMI G85 compliance・SECS/GEM compliance
-
-
product
Automated Wafer Handler up to 450mm
GPR-GB7S
The GB7S Robot System employs Genmark’s breakthrough and patented GPR™ Technology to achieve the highest level of performance currently available in an automated wafer handler which is capable of handling up to 450mm diameter wafers. The patented GPR technology enables the servo-controlled robot to interface compliantly and intelligently with misaligned cassettes, FOUPS and process modules, as well as provide software-controlled end-effector deflection compensation during transport of heavier payloads. The unique and patented YAW technology feature of the GPR-GB7S Robot System enables it to access in-line process modules, FOUPS and cassettes from a fixed centralized location, and eliminates the need for radial placement of process and other stations around the robot. The GB7 Robot System can have various arm configurations to accommodate a wide range of SMIF/cassettes front-end layouts.
-
product
Equipment Front End Module Wafer Handler
Sigma EFEM
Integration transforms the bond tester into a fully automated system. We offer various types of EFEM (Equipment Front End Module) wafer handlers, to combine with a Sigma W12 for operator-free bond testing.
-
product
Super Fast Gang Industrial Universal Programmer
48Pro2AP
The Dataman 48Pro2AP is a super fast industrial universal programmer with ISP capabilities and USB 2.0 connectivity • Optimised for use in automated handlers and ATE machines • Over 71,000 devices supported with new devices added monthly • Mechanically stable case design with multiple fixing points • ISP capable using the JTAG interface • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Comprehensive 3 years parts and labor warranty • Free life-time software updates
