Filter Results By:
Products
Applications
Manufacturers
- Optomistic Products
product
S2 Blinx Digital Sensors
ULP-S2 BLINX
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
product
Piezoelectric Sensor Group
This section introduces piezoelectric sensor products best suited for measuring, testing, and diagnostic equipment, such as accelerometer, acoustic emission (AE), and force sensors.
-
product
Force Sensors
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
product
New Link system Control and Image Capture Software
New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured parametersTrigger I/O for synchronisation with other equipmentTriggers recorded and plotted row by rowAutomatic setup of controls and parameter limits based on stage type connectedFull five point temperature calibrationUSB 2.0 to T96 and CSS450 ControllersOptional modules including Linkam Imaging Systems with high performance camerasIncludes .NET Components for easy integration into 3rd party applications e.g. LabViewNative 64 bit application
-
product
MEMS DC Response Accelerometers
PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.
-
product
Linear Stages
A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor is better than 10 nm. All NMT modules can easily be fixed onto each other. Very small connectors allow the exchange of a module without removing cables. The NMT-Zxx are modules for vertical movement. They have an internal load compensation to lift up loads. Nanomotor-Grippers and force sensors that can easily be fixed on these modules are available.
-
product
Torque Sensors
TE Connectivity (TE) offers solutions for measuring reaction torque and rotating torque. Our torque meters, complete with integral mechanical stops, increase overload capacity and provide additional protection during mounting and operation. We offer a variety of small capacity sensors for dynamic and reaction torque measurements. Our combination sensors simultaneously measure reaction torques and forces with a single device; these sensors can also detect angle position and provide velocity measurement. We can customize a wide range of available models to meet your specific needs.
-
product
Force Sensor Elements
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
Wireless Load and Force Measurement
Wireless ELF
The Wireless ELF 2 System is a user-friendly, cost-effective load measurement system. This system combines 3 FlexiForce WB201 sensors, battery-operated WiFi transmitter (certified 802.11b radio- 802.11b/g/n compatible), and Windows-compatible software*, turning your PC or laptop into a force measurement instrument. The WELF2 system, sampling rates up to 200 Hz and comes in a high speed version with sampling rates up to 6,000 Hz. The WiFi connection setup has ad hoc and access point (unsecured router) network capability. For multi-handle use an unsecured router is required.
-
product
Airlock Control System
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
product
Data Acquisition Systems & Data Loggers
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
product
Force Sensors
Specially designed for overseeing manufacturing processes. It measures with high consistency the regularity of compression load generated when fitting pieces.
-
product
Standard Flexiforce Sensors for Force Measurement
FlexiForce
FlexiForce force sensors are ultra-thin and flexible printed circuits, which can be easily integrated into force measurement applications. These sensors are available for purchase in our online store.
-
product
Signal Conditioner
ClipX
Fast and digital signal conditioning for force sensors, load cells, torque sensors, pressure transducers, as well as temperature and standardized signals (current/voltage). Guaranteed measurement accuracy, even in harsh industrial environments with electrical interferences.
-
product
Quartz ICP® Links
Link-style sensors measure dynamic compression and tension. They are constructed using a force ring that is under compressive pre-load between threaded mounting hardware. The threaded mounting on both ends of the sensor supports integrated link-style installations. Versions offering full-scale measurements of 10 lb to 50k lb (45 N to 220k N) compression and 30k lb (130k N) tension are available.
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
product
Force Sensors For Pull/push Direction
INELTA Sensorsysteme GmbH & Co. KG
The force sensors can be integrated easily and uncomplicatedly by the regular standard thread.
-
product
Tactical Video Data Link
Tactical Video Data Link (TVDL) is a video and data receiver/transmitter system specially designed for attack helicopters. This compact and lightweight system, weighing less than 4 kg, enables real-time, high-quality video imagery and data captured by UAV payloads or ground-based sensors to be displayed directly to the aircrew. This saves the need for lengthy radio dialogue by creating a common visual language amongst all forces in the battlespace and dramatically shortening the sensor-to-shooter loop. As a true video relay, the system can simultaneously transmit video and data as well as deliver imagery captured by onboard payloads to tactical forces for enhanced coordination and battle management.
-
product
Load/Force/Torque Sensor
Load cells and force sensors engineered and manufactured by Stellar Technology can be found in industrial applications all over the world. These include market sectors such as aerospace, oil & gas, automotive,
-
product
Load Monitoring Units (LMUs)
Magtrol's Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol's Load Measuring Pins and Load-Force-Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains DIP-switches and jumpers for greater flexibility and complete adaptability
-
product
Multi Axis Load Cells
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
product
Centor Dual R, 2 channels force gauge, external load cell
CNR DLR
The force gauge Centor Dual R series have all the functions of a Centor STAR R force gauge. And thanks to its ability to read two sensors simultaneously with a 500 Hertz sampling rate per channel, the force gauge Centor Dual is a true test console. It offers all of the functionality of an efficient force gauge, its calculating power enables it to save values from two different sensors simultaneously, to monitor set points and to perform calculations on each channel.
-
product
DMS Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Digital Weighing Indicator | Process Meter | Panel Meter
Mantracourt’s digital weighing indicator and panel meter modules are compatible with a wide range of sensors and transducers, including volts, amps, temperature, frequency, speed, load, force, pressure, torque, LVDT, RVDT and many more. The digital architecture offers simple one-pass calibration and fast setup.
-
product
3-Component Quartz Force Links
261 Series
Three-component force links eliminate the preload requirement of 3-component quartz force ring sensors, and offers a convenient, 4-screw hole mounting plate on each side end the sensor. Quartz 3-component force links are constructed by installing a 3-component force ring sensor, under preload, between two mounting plates.
-
product
Shear Beam Force Sensors For Pull/push Direction
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
product
Torque Transducers
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
product
Force Sensors For Push Direction
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges (DMS)
-
product
Pressure-Force Cables And Connectors
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
product
Strain Sensors
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
