Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc.
product
Connector Board for Cable and Harness Tester
CB49
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
product
MI/O Extension Modules and Evaluation Boards
Advantech‘s MI/O extension modules and evaluation boards are designed for MIOe embedded single board computers (SBC) to extend functions such as USB 2.0/USB 3.0,and provide additional I/O interfaces via a high-speed connector.
-
product
MicroSemi-SiC-Module / Evaluation Board
EV-MS4135PL1Z-U1 Pre-Release
High power evaluation board, up to 1200V & 50A @ 200kHz switching frequency featuring the combo ADI ADuM4135 isolated gate driver + LT3999 isolated power supply controller + Microsemi SiC power module in half bridge configuration.
-
product
Evaluation Kit
ROM-3310 Development Kit
*Evaluation kit for ROM-3310*Lower power TI sitara AM3352 1GHz processor*On board DDR3 512MB memory / 4GB Flash*HW WDT for system protection*Supports 1 GbE, 1 USB 2.0, 1 USB 2.0 OTG, 2 CANbus, 10 GPIO, 4 UART,1 I2C, 1 I2S, 1 SPI, 1 SDIO*Cable pack & Panel included*Evaluative image & test utilities built-in
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
Evaluation Board
emPower
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
product
FRAMOS SLVS-EC RX IP CORE
Sony’s SLVS-EC interface standard has emerged as the best high speed interface to Sony’s best image sensors, enabling higher throughput, greater signal integrity, and simpler designs. Engineers developing solutions using Xilinx FPGAs and SoCs can take advantage of FRAMOS’s SLVS-EC RX IP Core, Evaluation Board and tested source code examples. Device builders and camera vendors can de-risk the design while reaping the benefits of Sony’s latest high-speed interface.
-
product
Air Quality Click
64202
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
PCI Evaluation Board
BCM91125E
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
product
Carrier Boards
ROM-DB5901
ROM-DB5901 is an evaluation carrier board designed for the Advantech SMARC v2.0 module. It is compatible with the ROM-5720, ROM-5620 and ROM-5721 SMARC modules and has a multiple I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and two MIPI connectors for the camera module. ROM-DB5901 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems
-
product
Carrier Boards
ROM-DB7503
ROM-DB7503 is the Referenced Carrier Board designed for Advantech's Qseven 2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. it's more easier for the end user to design portable devices by referring ROM-DB7503 design.
-
product
VME & VPX Evaluation & Development
EZ Platforms
Kontron provides a solution for a quick entry into the evaluation and development of VME and VPX applications. EZ turnkey platforms are compact air-cooled rack systems with pre-integrated VME or VPX board along with the associated rear transition module (RTM) and pre-loaded software. Engineers with no prior VME or VPX expertise can start application development in seconds.
-
product
Development Kits
Advantech development kits includes a series of carrier boards and starter kits with schematic software and reference design to accelerate evaluation.
-
product
Camera Modules
e-con Systems Camera Modules come with parallel & MIPI interfaces. Our CMOS camera modules will be effective in any application or environment because of their versatility and wide range of options. Embedded camera module can be interfaced to processors like Tegra K1, i.MX6, DM3730, OMAP. Further to these HD camera modules, e-con offers evaluation boards with these camera modules interfaced to various development boards featuring these processors. We provide Omnivision Camera Module & Aptina Camera Module (ON Semiconductor) with CMOS Sensors.
-
product
LSM6DSL Click
64207
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
Dynamic Data Simulator
LS-70-S
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
product
Proximity 3 Click
64211
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter. Proximity 3 click is an intelligent proximity and light sensing device, which features the VCNL4200 sensor from Vishay – high sensitivity long distance proximity sensor (PS), ambient light sensor (ALS) and 940 nm IRED, all in one small package.
-
product
13MP Camera Board For I.MX8
E-CAM130_iMX8
e-CAM130_iMX8 is a 13MP 4-lane MIPI CSI-2 autofocus color camera board for iMX8 family of processors. The e-CAM130_iMX8 camera board is interfaced directly to the CSI-2 MIPI interface on the Variscite's DART-MX8M/DART-MX8M-MINI Evaluation kit (VAR-DT8McustomBoard). The iHDR (interlaced High Dynamic Range) support helps to capture good quality images in both high and low illumination. e-CAM130_iMX8 also comes with a high-performance Image Signal Processor (ISP) that performs all the Auto functions (autofocus, auto white balance, auto exposure control). Customer who wants to integrate this camera into their end product can directly purchase e-CAM130_MI1335_MOD camera module.
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
SMARC
SMARC (Smart Mobility Architecture) modules are ultra-small system-on-modules targeted towards applications that demands compactness and energy-efficiency. The SMARC system-on-modules also support Axiomtek evaluation carrier boards for easy integration and hardware design reference.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
product
MPU 9DOF Click
64219
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
Software
TestPoint-based software for control, measurement and evaluation of electrochemical measurements, requires MS WindowsTM supports or interfaces,. CPC manages potentiostat control, data recording and data evaluation.Features: Up to 6 measurements channels, fast data access up to 300,000 data points per second. The evaluation allows differentiation, Tafel slope evaluation and other helpful routinesCPC runs with many multi-function AD/DA converter boards. It requires MS Windows (TM)
-
product
Carrier Boards
ROM-DB7501
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
product
Evaluation boards
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
product
Sensor for Filament Inspection
EyeFI
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
product
Carrier Boards
ROM-DB7502
ROM-DB7502 is the Referenced Carrier Board designed for Advantech's Qseven 2.0/2.1 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7502 design.
-
product
PCI Evaluation Board
BCM91250E
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
product
Time Sensitive Networking Evaluation-Kit
The evaluation kit offers developers the possibility to test and evaluate Ethernet TSN for their own applications. It consists of either a Smartzync board (Xilinx) or a Netleap board (Intel/Altera) with an optionally implemented IPMS TSN-IP core for endpoint applications (TSN-EP), switched endpoint applications (TSN-SE) or switch applications (TSN- SW). Linux drivers with application examples, as well as RTOS test applications and TSN network configuration examples are also available.
-
product
Carrier Boards
ROM-DB5900
ROM-DB5900 is an evaluation carrier board designed for the Advantech SMARC module. It is compatible with SMARC module ROM-5420 and has a rich I/O interface for evaluation and development. It supports wide range operating temperatures, two power input interfaces, and also supports two MIPI connectors for the camera module. ROM-DB5900 is an ideal development board for mobile applications, such as portable devices, industrial tablets or HMI systems.
