Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Acoustic Test Chambers
Small Device Test Chambers are used for >Basic sound level measurement of small products and equipment >Pre-compliance testing of small products and equipment >End of line manufacturing test on small products and equipment Small Device Test Chambers provide acoustic isolation from outside sounds and/or reduce the sounds from the device under test radiating into the host
-
product
EOL RF Functional Test
AS652
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
product
Trackside Equipment
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
product
End of Line Noise Test System
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
product
Cycle-ATV Dynamometers
EC997
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
product
Integrated USBL Acoustic Tracking and Communication Systems
The TrackLink systems are the world's best selling USBL acoustic tracking systems with fully integrated high speed acoustic communication capability. Capitalizing on its benchmark Broadband Acoustic Spread Spectrum (BASS) technologies, LinkQuest provides the end users with solutions for underwater tracking and communication at sharply reduced cost and increased robustness. An extensive line of models are available to suit the users' specification and budget constraint.
-
product
BATTERY PACK AND BMSTEST SYSTEMS
DMC's Battery Pack Test Systems facilitate battery design as well as research and development for national laboratories and research institutions. They are deployed in end of line / production test stations for battery packs developed by major automotive manufacturers and their suppliers. DMC's battery pack test systems are designed to evaluate the battery as a complete system and validate a comprehensive range of battery pack functionalities, including:Power performance, Capacity, DCR / Internal ResistanceContactor and safety interlock functionsIsolation / Insulation ResistancesReporting of operating data through external communication interfaces (usually CAN)Cell VoltagesPack / Cell TemperaturesState of ChargeFaults / Diagnostic Trouble Codes (DTCs)Etc.Electrical characteristics / continuity of internal pack wiring / signalsCooling system operation
-
product
Inductor Test & Packaging Machine
1870D
The Chroma 1870D Series (1870D/1870D-12) are specifically Designed automated test equipment for chip inductors. It comprises Various test functions that are required for verifying chip inductors. In addition, an automated tape packaging machine at the end of production line is equipped to fulfill demand for automated manufacturing.
-
product
EOL Tester
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
product
In-Line Fat Measurement
FATSCAN
TOMRA’s new FatScan fat analyzer allows for the continuous analysis of meat to precisely determine its fat content. This functional and compact machine can be easily integrated in production lines and is specifically designed to assist smaller meat processors in delivering a consistent and uniform product. The innovative FatScan can analyse both fresh and frozen meat and it measures fat in real-time, delivering highly accurate and consistent results. The hygienic and robust analyser penetrates deeply into the meat, and measures across the full 500 mm width of its conveyor belt. The design is open, so all surfaces can be visually inspected and sanitized, using high pressure water. The FatScan is able to analyse up to 7 tons of meat per hour, making it an ideal choice for small and medium size processors. This, along with the consistent end product quality and savings generated through reduced lean give-away, helps you to drive up your profits.
-
product
Graphical Power Quality Analyzer
PS5000
The PowerSight PS5000 Power Quality Analyzer is the premier member of the PowerSight line of compact, versatile, easy-to-use power quality analyzers. It provides the Most Efficient and Error Free Solution for doing Power Studies.The full color display eliminates the need for laptops to see waveforms and logs. Phasor diagrams provide quick verification of connections.The visual presentation of potential errors in connections and settings, via SureStart, minimizes the risk that the data will be incorrect at the end of the study.The graphical user interface allows easy changing of trigger thresholds.The large screen and “soft keys” allow quickly viewing all measurements of interest quickly.
-
product
Linear Actuators DCG Controls
DCG
Thomson now offers a small, lightweight line of 24 VDC units in its DCG family of controls. The DCG controls feature built-in Electronic Limit Switches (ELS) to stop actuator movement automatically at a mid-stroke stall point and end of the stroke. Additionally, synchronous operation of some actuators equipped with encoders is possible.
-
product
BottleChek
The BottleChek Metal Detector Conveyor is designed to inspect pharmaceutical bottles or vials at the end of the packaging line for unwanted metallic particles. The system easily integrates into any production line for side-by-side transfers.
-
product
Function Tester with Low Number of Channels
UTP 6010 RF
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
product
Multi-Purpose Probes
*For All your Functional Test Needs *Machine Building *end of line test
-
product
Loop A Line
TX916
The Loop a Line has been a Telstra standard for 20 years. It is probably the simplest time saving device available for contractors and technicians. Once fitted to the far end of a line you can switch between Open, Short, Connect, 600 ohm, and Tone modes allowing all installation and fault location to be performed from the one end without having to go back and forward from one end of the line to the other.
-
product
Electroluminescence Test Systems
The products of the SolarModule EL-inline family are integrated into a module production line, before lamination, after lamination or at the end directly after the performance measurement. High-resolution cameras provide excellent image quality and allow the automatic detection of relevant defects. A manual evaluation of images is no longer necessary, which means that considerable costs can be saved. Communication to upstream and downstream processes is flexible and can be adapted to all common interfaces.
-
product
Infrared, Near Infrared and Raman Spectroscopy
rom the very compact FTIR spectrometer to the world’s highest resolution: Bruker offers the industry's largest selection for demanding routine and High End FTIR research application including the new and unique verTera cw THz functionality.Process monitoring with FTIR / FT-NIR process spectrometers.A complete line of Near Infrared Spectrometers to fit all your needs, including Process Monitoring.FTIR Microscopy and Raman Microscopy and Spectral Imaging for high sensitivity at high spatial resolution.High spectral resolution, high performance Raman and FT-Raman spectrometers for advanced routine solutions.FTIR Gas Analyzers for the fully automated and high precision real-time monitoring of gas compoundsImaging Remote Sensing systems for analysis of gases, liquids and solids.CryoSAS semiconductor material quality control for photovoltaic and electronics industry.OPUS, the "all-in-one" IR and Raman spectroscopy software consists of a suite of software packages that cover both standard and specialized applications.ONET, software for the setup, administration and control of large FT-NIR spectrometer networks.
-
product
EOL/Functional Testing
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
product
Multifunctional Safety Tests
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
product
AC Power Line EMI Filters
CleanSweep®
CleanSweep® filters block EMI on power lines (both common and differential modes) and, uniquely, in ground, from reaching sensitive equipment. They also reduce EMI "backflow" from a "noisy" source that otherwise would end up on your AC power network.
-
product
ACCUplace BullsEye /Recognition Grid
AP-B Series
A unique concept in imaging calibration technology, The ACCUplace Bulls Eye / Recognition Grid allows the end user to calibrate magnification at multiple power levels, as well as test the system’s ability to recognize and locate distinctive shapes within shapes by focusing on the concentric circles.Each Bulls Eye / Recognition Grid target has individual patterns consisting of 5 concentric circles with 0.50mm line width and 0.50mm spacing between circles (10mm Pitch) with a 0.100mm center dot. In addition, each row and column is labeled with X & Y coordinates. The AP-B series is offered on four standard substrates; Chrome on Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
product
Lumber Moisture Measurement Systems
Improved moisture control has emerged as an important process improvement element in the forest products industry as mills continue to focus on profitability and yield. SCS Forest Products by Finna Sensors provides the industry’s widest-used end-to-end line of integrated moisture measurement systems and related process optimization tools for the sawmill, kiln and planer.
-
product
EOL Testing of Speed Sensors
Complete programming and end of measuring stations integrated in the assembly line for rotary electronic sensors with automatic sensor recognition.
-
product
Non Contact Flange Torque Transducer
FF425
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
product
Protection System Tools
Megger’s comprehensive range of products for relay tests includes high current primary injection, relay phase angle, end to end line protection GPS timers and relay current amplifiers.
-
product
Fast LID Measurements for EOL
KMP
TechnoTeam Bildverarbeitung GmbH
The KMP is the solution to cost-effectively bring indirect light measurement technology to places with too little space for a BV room. Its lightweight and compact design allow it to be integrated into production lines, positioned next to production or in a small lighting lab.
-
product
In-situ Wafer Temperature Monitoring
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
product
Universal Test Fixture
Series 48
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
