Filter Results By:
Products
Applications
Manufacturers
Design Verification
Examination of design requirement fulfillment.
- Pickering Interfaces Inc.
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm - SPST
40-294-114
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Peak Power Analyzer
4500C
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm - SPST
40-294-131
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
IC Design & Verification
Mentor Graphics provides best-in-class products for IC design. Calibre for physical verification, extraction, resolution enhancement and mask data preparation, ADVance MS for analog/mixed-signal simulation and an integrated tool flow for custom IC design
-
product
USB Protocol Verification System
Voyager M310e
The Voyager M310e is Teledyne LeCroy's flagship USB protocol verification system designed for USB 2.0, USB 3.2, Type-C, and USB Power Delivery. Offering the industry's highest fidelity probe design, flexible traffic generation, and a range of turnkey Compliance packages, the Voyager M310e is the most complete platform for cradle-to-grave USB design verification.
-
product
Metrology
KLA’s metrology systems address a range of chip and substrate manufacturing applications, including verification of design manufacturability, new process characterization and high volume manufacturing process monitoring. By providing precise measurement of pattern dimensions, film thicknesses, layer-to-layer alignment, pattern placement, surface topography and electro-optical properties, our comprehensive set of metrology systems allows chip manufacturers to maintain tight control of their processes for improved device performance and yield.
-
product
Waterproof Test Chamber
JL-XC
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm
40-294-033
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm
50-294-014
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Sofyware
BuildIT Construction
BuildIT Software & Solutions Ltd.
BuildIT Construction is a construction verification software solution that enables AEC professionals to facilitate and accelerate prefabricated part positioning and monitoring, validation to BIM and project evaluation with high accuracy by using 3D analysis in adherence to design and structural specifications. Utilizing BuildIT Construction allows users to drastically reduce costs and detect errors early on to avoid expensive rework. Leveraging the robust and powerful platform of BuildIT’s cutting-edge 3D metrology software for manufacturing, BuildIT Construction addresses all quality assurance and quality control processes throughout the building and facility lifecycle.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Rain Test Apparatus
Wewon Environmental Chambers Co, Ltd.
The main function of the rain test apparatus is to test the physical and other related properties of electronic and electrical products, such as lamps and lanterns, electric cabinet and electrical components, under the simulated weather condition of rain. After the test, the performance of the product is judged to meet the requirements through verification. Use this way to improve the product design, verification the use and quality inspection before delivery.https://www.wewontech.com/rain-test-apparatus/
-
product
DC Blocks
BroadWave designs and manufactures DC Blocks and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
Universal Test System
LS6601A
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
product
PXI RTD Simulator Module 18-Channel PT1000
40-262-002
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm
40-294-024
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Portable Sequence Generator for Verification, Firmware & Validation
ISequenceSpec
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Interconnect Testing
iTest allows you to design and group your own specific interconnect test schedule, choosing only the call test you wish to use such as Originating or Terminating party call disconnects, long duration calls, CLI verification, DTMF and correct disconnect code responses.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
AC Power Source
6500 series
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
product
Static Design Verification
ALINT-PRO
ALINT-PRO™ is a design verification solution for RTL code written in VHDL, Verilog, and SystemVerilog, which is focused on verifying coding style and naming conventions, RTL and post-synthesis simulation mismatches, smooth and optimal synthesis, correct FSM descriptions, avoiding problems on further design stages, clocks and reset tree issues, CDC, RDC, DFT, and coding for portability and reuse. The solution performs static analysis based on RTL and SDC™ source files uncovering critical design issues early in the design cycle, which in turn reduces design signoff time dramatically. Running ALINT-PRO before the RTL simulation and logic synthesis phases prevents design issues spreading into the downstream stages of design flow and reduces the number of iterations required to finish the design.
