Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Instrumentation Modules For Automated Test Systems
PXI-based test systems often require a variety of general-purpose instrumentation such as digital I/O, waveform generators, voltage & current sources and DUT power supplies.
-
product
Shock Testing
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
product
High Current SMU Family 2000 A
AXC76xx
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
Ground Continuity Test Instrument
MODEL M25
Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures AC resistance from Chassis of Device Under Test (DUT) to power-cord ground lead - 0 to 0.15 ohm
-
product
Modulation Distortion For E5081A Up To 44 GHz
S960707B
The S960707B modulation distortion software application provides nonlinear DUT behavior tests (EVM, NPR, and ACPR) under modulated stimulus conditions.
-
product
Tunable Non-Reflective Band-Reject Filter (700MHz-1GHz)
SPCL-00597
This device is placed after the DUT to protect the Spectrum Analyzer from high-power fundamentals and provide harmonic measurements. The non-reflective functionality prevents energy from bouncing back to the DUT and raising the noise floor level.Broadband matching improves dynamic range and reducesmeasurement uncertainty.
-
product
PXI/PXIe Source Measure Unit Family
PXS(e)840x
The PXS840x PXI SMU family is a high-speed, 4-quadrant source measure unit. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
Power Supplies
AC and DC power supplies are used for providing the power required for energising the trip and close coils of the breaker and for running the spring charging motor. The appropriate AC or DC configuration of the power supplies can be selected, depending on the DUT specifications of the manufacturer. Dual-mode AC/DC power supplies capable of providing AC and DC outputs from the same power supply are also available, if required by the user.
-
product
Adjustable Multisite Rail System™
The Celadon Rail System allows multi-site testing capability with flexible die to die spacing using existing Celadon VersaTiles™ to minimize cost of test with new DUT structures. The modular design allows for additional site assemblies and rail assemblies to be added after the original system purchase. With the Celadon Light-Tight Enclosure and Rail System Tool, high accuracy alignment and testing can be performed at extreme temperatures without affecting the thermal equilibrium of the system.
-
product
Ground Continuity Tester - 25, 30, 35 AMP
M25, 30, 35
Production / Quality Assurance Testing - Performs ground continuity tests in full compliance with BSI, VDE and IEC. Measures ground continuity from ground to the power cord ground pin of the DUT. Interface enables interconnection to any ROD-L Hipot & Leakage testers to form a complete automatic test system.
-
product
Solar Array Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
product
Automatic Calibration Module
ACM2520
ACM2520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full 2-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
product
ENA-X Vector Network Analyzer
E5081A
Our spectral correlation technique directly analyzes the modulated input and output signals in the frequency domain on the network analyzer. Current solutions on the market require a network and spectrum analyzer to characterize components fully. With the new ENA-X, you can ensure test accuracy and repeatability with a single test setup using full vector correction at the DUT plane. Avoid manually reconfiguring setups or automating complex switch-based systems — verify device performance faster and with less error potential with the ENA-X network analyzer.
-
product
Test Fixture Kits
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
product
P-Series Single Channel Power Meter
N1911A
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
product
Test/Debug Bench Station
No. of Tahoe Drivers: 1 (1:1 Driver/BIB ratio)No. of Voltages available per BIB Slot: (16 (PS1…PS16)Same Dynamic Stimuli, DUT Monitoring and Sierra™ Software as the system.
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
product
Optical Spectrum Analyzer Module
OSAPXIe
OSAPXIe enables new measurement capabilities in PXI for truly effective mixed-signal testing. Conduct all your DUT characterization from one platform and spend less time switching cables and patchcords between instruments.
-
product
DC Power Module, 35V, 1.5A, 50W
N6734B
The Keysight N6734B is a 52.5 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
product
IOL & Power Cycling Test Systems
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
product
Vibration Unit Tester
BK2020B
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versatile. It can be set up as a stand alone machine, or used with a PC and software for access to more information, and to save the data for analysis. Either version is great on the product line but you may also use it for QA, QC and development.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Scalar Network Analyzer Extenders
A Scalar Network Analyzer is a type of RF network analyzer that is used to measure only the amplitude properties of a DUT (Device Under Test). Unlike a Vector network Analyzer, it does not measure both amplitude and phase of the DUT.
-
product
ICT Software: Interactive Developmetn Encironment ICT ICE & ICT Sequencer
ICT IDE and Sequencer
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
product
Vector Network Analyzer
ZNBT
The R&S®ZNBT is a multiport vector network analyzer offering up to 24 fully integrated test ports. The instrument can simultaneously test multiple DUTs or measure one DUT with up to 24 ports. The fully integrated test ports make the R&S®ZNBT a true multiport vector network analyzer, which includes a wide dynamic range, high output power levels and fast measurements. Frequency ranges up to 40 GHz are avalailable.
-
product
DC Power Module, 8 V, 6.25 A, 50 W
N6732B
The Keysight N6732B 50 W basic DC power module provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power your DUT or ATE system resources, such as fixture control.
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
product
Plane Wave Converter
PWC200
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
product
RF Device Tester
RF ITS
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
