Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
NVIDIA® Jetson Xavier™ NX Edge AI Vision Inference System
EOS-JNX Series
The EOS-JNX series has a built-in Smart PoE feature to control PoE power remotely to reduce maintenance efforts in challenging environments and provides PoE power loss detection to alert of any unexpected PoE disconnection. The EOS-JNX-I is designed as an AI PoE switch for connecting to IP cameras to enable AI inferencing, and also provides an uplink port to connect to a network video recorder (NVR) for recording video streams, making upgrading existing surveillance systems easy. The EOS-JNX-G is designed for industrial AI machine vision applications, providing a dedicated bandwidth of 1Gb per channel with a GigE camera connection, which is crucial for production line and manufacturing applications.
-
product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
Vibration Control, Monitoring and Diagnostics System for Hydraulic Units
Stationary system for vibration control, monitoring and diagnostics of hydraulic units is used for constant technological and safety control, diagnostics of vibrational and mechanical parameters of hydraulic units and auxiliary equipment of hydroelectric power stations in accordance with the applicable requirements.
-
product
SPM Control System
Nanonis
SPECS Surface Nano Analysis GmbH
Unbound to any specific microscope, the Nanonis SPM Control System is designed for the uncompromising demands of scientific excellence in a wide variety of SPM applications. Its modular concept implemented in a fully digital fashion is carefully thought through, with a strong emphasis on usability, stability and flexibility.
-
product
New Link system Control and Image Capture Software
New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured parametersTrigger I/O for synchronisation with other equipmentTriggers recorded and plotted row by rowAutomatic setup of controls and parameter limits based on stage type connectedFull five point temperature calibrationUSB 2.0 to T96 and CSS450 ControllersOptional modules including Linkam Imaging Systems with high performance camerasIncludes .NET Components for easy integration into 3rd party applications e.g. LabViewNative 64 bit application
-
product
Occupational Noise Measurement System
NK122
This Occupational Noise Measurement System is designed to give Health and Safety Managers, or any other professional with responsibilities for managing noise in the workplace, everything they need to protect your workforce from over exposure to noise and to help you ensure your company is complying with The Control of Noise at Work Regulations 2005.
-
product
Terahertz Spectroscopic System
TAS7400
The TAS7400 product line offers a series of low-cost, all-purpose spectroscopic systems that enable spectroscopic measurements using terahertz (THz) waves. The tools are capable of performing non-destructive analysis on a wide variety of sample types, making it applicable to a broad range of fields from life sciences to electronics, where precise chemical and material characterization is critical. The systems are ideal for settings ranging from basic research to product development, as well as for manufacturing and quality control, and employ easy-to-use spectroscopic methods that do not require specialized knowledge of THz wave generation or optics.
-
product
Digital Digitizer
MOS2
Mezzanine module (mezzanine) MOS2 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values. The mezzanine is intended for use in HF and microwave systems as a terminal device for digitizing intermediate frequency signals up to 200 MHz. Together with the frequency converter DOWNCONVERTER 10 GHz LXI manufactured by the holding "Informtest" MOS2 under the control of the common software shell ACM2 makes up a synthetic instrument - spectrum analyzer, a ready-made solution for testing microwave devices and radio reception channels.
-
product
Residual Current Protection
Solutions to ensure the safety of people and installations against any ground currents. Available with ultra-immunized system as an essential solution to avoid financial losses due to outages caused by inadvertent trips. Specially designed to protect industrial installations in AC networks (type A), installations with both AC and DC components and DC-only installations (type B). Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
Ultra-Wideband Tunable Laser
Full-band TSL
The system combines up to four of our tunable lasers (TSL-570) with an optical switch module (OSU-110) and control software. The complete Full-band TSL has excellent cost performance, high wavelength accuracy and fast sweeping for use in both R&D and production environments.
-
product
External Input Module
EIM-01
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
product
Intelligent Power Switches
ST offers a series of intelligent power switches (IPS) for high-side and low-side configurations. These devices integrate the control section (logic interface, drivers, diagnostic and protection features) and the power stage on the same chip, with benefits in terms of compactness, increased system reliability and cost effectiveness.
-
product
PXI Strain Gauge Simulator Module 2-Channel, 2K
40-265-302
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Multiphoton FLIM System
DCS-120 MP
*Multiphoton FLIM Upgrade for Existing Conventional Microscope*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Scanning by Fast Galvanometer Mirrors*Channel Seperation by Dichroic or Polarising Beamsplitters*Individually Selectable Pinholes and Filters*Excitation by Ti:Sa Laser*Two Non-Descanned Detection Channels*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: Two HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Electronic Pinhole Alignment*Z-Stack FLIM Acquisition with Zeiss Axio Observer Z1*Optional: Spatial Mosaic FLIM via Motorized Sample Stage*Laser Control via SPCM Software
-
product
RFP DC Low Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
24-Bit Precision Load Cell Input Card
PCI-9524
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
product
Universal Ground Control Station
UGCS
UGCS is the common control station for the U.S. Army's Shadow®, Hunter and Gray Eagle™ unmanned aircraft systems. Built on a flexible crew station architecture, the UGCS can be configured and housed based on customer requirements, supporting a wide variety of assets and operations.
-
product
Converter
556
The dual channel converter 556 provides continuous inline, real-time measurement and control of turbidity. The customer’s specific factory calibration of the converter can be configured in ppm (DE), FTU or EBC. Combined with an optek TF56-N scattered light sensor the 556 converter is a cost-saving measuring system, providing reliable process measurements.
-
product
Energy Solutions
Energy is a complex field with a broad array of concerns, including energy security, environmental and operational protection, system efficiency, distribution system reliability and control, and clean energy technologies.
-
product
Multi-Channel Voice Communications Platform
Mercury ES
Mercury ES is a multi-channel voice communications platform that operates on LANs/WANs over terrestrial or satellite-based IP networks offering global coverage. Users access the system via browser-based control panels with up to 256 call buttons and an impressive 32 channel capacity.
-
product
PCIe-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
786456-01
PCIe, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The PCIe-7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe-7846 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Independent Operation AC Generator Excitation Regulator
SVRi
Kinetics Control Systems SVRI Exciter/Regulator rectifier is designed and rated in capacity for the application of exciting the DC fields of an AC generator operating independently with other generators and/or NOT tied into a utility power grid.
-
product
VLF Diagnostics System
PHG 70 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
product
In-Line Spectroscopic Ellipsometer for Web Coater and Roll to Roll Systems
UVISEL
The UVISEL Spectroscopic Phase Modulated Ellipsometer is a turn-key thin film metrology instrument for in-line measurement of thin film thickness and optical properties. It features rapid measurement capability with data acquired every 50 ms for powerful control of thin film uniformity across the entire web.The design of the UVISEL ellipsometric heads allows simple integration into roll-to-roll systems, while the software provides advanced communication capabilities suited to roll-to-roll production.
-
product
CMOS Cameras
Magic series
New Imaging Technologies proposes a broad range of visible products. From sensors to complete camera systems, all of our products integrate our unique NATIVE WDR capabilities. Our NATIVE WDR™ is a new generation of CMOS imaging technology named MAGIC™ (standing in english for Active Matrix with indexed generated contrast ), capable of generating a highly stable image even under very wide intra scene dynamic range (> 120dB) in a single frame time and without multi-exposure, any setting of knee points or external control. Our products are suited for many demanding applications and industries.
-
product
PICMG 1.3 Half-size CPU Card With LGA1150 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q87, SATA3, USB 3.0, DVI-I/LVDS And Dual LANs
SHB230
The SHB230 is high-performing PICMG 1.3 half-size single board computer.The SHB230 based on the Intel® Q87 PCH is designed to support 4th Generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Haswell/Haswell Refresh) in the LGA1150 socket.The slot CPU card is equipped with two DDR3-1333/1600 SO-DIMM sockets with up to 16 GB memory capacity to meet customers needs.The PICMG 1.3 specification brings advantages of PCI Express to this single board computer that offers four PCIe x1 or one PCIe x4, and one PCIe x16 routed to the backplane.The onboard two SATA interfaces support RAID 0/1 functions to ensure reliable storage for multiple applications.Utilizing with the latest Intel® technologies, this PICMG 1.3 system host board is an ideal solution for DVR, medical equipment, industrial automation, process control, and network security market.
-
product
Portable Bridge Structures Control System
Portable bridge structures control system is a set of digital modules and intelligent sensors placed inside of a compact case. Basic delivery scope of the system includes:
-
product
VOA DWDM with EDFA With VOA, EDFA Dense Wavelength Division Multiplexer
DWDA-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDA-1000 series is integrated by DWDM, VOA and EDFA module in a 1RU or 3D rack. Each channel of DWDM with a high-resolution factor electronic control adjustable optical attenuator will adjust and equilibrium the power. The insertion loss, power loss because of the channel equilibrium of DWDM will be amplified and compensation by the build-in gain flatness EDFA. Compact and simple device structure, thereby reducing the connections between devices to improve the index and reliability of the system. Can be used in DWDM system power equilibrium, optical add and drop multiplexed (OADW) flexible and expediently.
-
product
Test & Measurement Platform
Konrad System Manager
The Konrad System Manager is the central tool for the Konrad test and measurement platform. It combines execution, interactive supervision and documentation of the installed Konrad test modules.- Displays the live status of the module functions in parallel to running test executions- Easy debugging of the switch routes- Control the modules functions- Configure device Alias name for modules- Display alias naming for switching channels- Execute selftest functionality of the modules- Display device information and documentation of the installed modules- Simulate modules
