Filter Results By:
Products
Applications
Manufacturers
Component
Testing of individual hardware or software components or groups of related components.
- Frequency Devices Inc.
product
Band Reject (Notch) Filter Components
precision band-pass and band reject (notch) active filters that provide high performance in a compact 32-pin DIP package, with a broad range of fixed center frequencies (fo) from 1 Hz to 100 kHz. Each filter type features a neartheoretical amplitude/phase response along with lowoutput voltage noise enabling these filters to achievea 10,000:1 or better dynamic signal range.
-
product
System Components
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
product
Residual Current Protection
Solutions to ensure the safety of people and installations against any ground currents. Available with ultra-immunized system as an essential solution to avoid financial losses due to outages caused by inadvertent trips. Specially designed to protect industrial installations in AC networks (type A), installations with both AC and DC components and DC-only installations (type B). Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
product
New Link system Control and Image Capture Software
New uncluttered and intuitive user interfaceLive display of current status for easy monitoringFull control of heating and cooling rate, limit and hold time of up to 100 rampsRow by Row control of Vacuum, Humidity, Tensile Force and Shear modes controllable and synchronised with TemperatureParameters of connected Linkam sensors displayed and stored - e.g. Vacuum, Humidity, Force, XY position and Pressure (dependent on connected stage type)Real Time chart of temperature and other measured parametersTrigger I/O for synchronisation with other equipmentTriggers recorded and plotted row by rowAutomatic setup of controls and parameter limits based on stage type connectedFull five point temperature calibrationUSB 2.0 to T96 and CSS450 ControllersOptional modules including Linkam Imaging Systems with high performance camerasIncludes .NET Components for easy integration into 3rd party applications e.g. LabViewNative 64 bit application
-
product
Virtual Platform Development and Simulation
DEV
The Imperas Developer products consist of tools, models and infrastructure components critical for the high quality, rapid development and verification of embedded software, utilizing virtual platforms. The Developer products provide the necessary capabilities to develop platforms, including software simulation capability to execute embedded code on the platforms.
-
product
64x64 Matrix
TS202A
Universal Switching Corporation
Designed from scratch to improve on the legacy Precision Filters Model 4164, the TS202A uses the absolute latest in component technology. Many engineers still use manual patch cords & patch panels to interconnect sensors, recorders, scopes and other instrumentation in test & evaluation labs.
-
product
Video Signal Distributor
MSMD-515D~915D
MSMD-Series is a slot type Multi Signal Distribution Buffer and it is named depend on number of slot. It is support PC signal (R, G, B, HS, VS), CVBs, S-Video (Y,C), Component(Y,Pb), Scart(European Type), Audio, DVD(Digital) & Optical Audio signal without any signal diminishing & distortion. Each slot operate as one distributor separately and it is efficient to test multi signal format at the same time.
-
product
Electromagnetic Express
EM-X
Is a physics modelling package for electromagnetic fields and charged particles. A CAD component allows the definition of mechanical parts and assignment of electric potentials, magnetization and charged particle sources. A time domain, particle-in-cell (PIC) tool then solves the electromagnetic fields and moves the particles within them. The particles’ own charges andmotions are fed back into the electromagnetic fields allowing the effects of space charge and selfmagnetism to be accounted for.
-
product
Fuel/Other Analyzers
Our products are used to test fuel in a couple of ways. Fuel blending is the process of ensuring a fuel has the desired composition in terms of relative concentration of components. Testing fuel for contamination ensures that the equipment that burns the fuel will not suffer damage from impurities in the fuel.
-
product
Digital to Synchro and Digital to Resolver Converters
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800A (1RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800A (1RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
product
C/L-Band ASE Light Source
ASE7000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE7000 series is C/L-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of C/L-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE7000 has three types of exterior structure, suitable for different customer’ requirements.
-
product
Anti-Surge Chip Resistors (Double-Sided Resistive)
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
AMP HOUND 2
AMP2
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Electro-Mechanical Assembly
Teledyne Marine Cable Solutions
We perform complete or partial assembly including hole-cutting, connector and component mounting, engraving, labeling, various coating applications, or any subset of that including purchasing, kitting, or partial assembly.
-
product
Versatile RF Network Analyzers for LF and MF
TE3000-series
The TE3000-series of RF vector network analyzers have full vector measurement capability, and accurately resolves the resistive, capacitive and inductive components of a load. The user can display the vector impedance plus a range of related parameters including SWR, reflection coefficient, return loss and R-L-C equivalent circuit.
-
product
Universal Breakout Test Fixture
CA-323
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
product
Accuscan XE200i
Rotary Precision Instruments UK Ltd
Fully understanding components geometry prior to assembly is critical when faced with the ever growing environmental pressures and increasing fuel prices. The significantly more reliable measurement data collected by AccuScan™ enables rotor stacking software to accurately manipulate component parts, resulting in precisely aligned rotor assemblies. AccuScan™ has been independently verified and proven to offer our customers significant operational improvements over their traditional measurement methods.
-
product
Simulating Optical Design Components
Wave Optics Module
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
product
terraTEM Receiver Coils
TRC
The terraTEM multi-turn receiver coils (TRC) are designed to be used in place of largTRC ver sideviewXe receiver loops, placed either inside or outside the transmitter loop with the measurement point being at the location of the TRC. The compact size of the TRC receiver, measuring just 0.6m x 0.6m x 0.33m, makes the multi-turn coils convenient to use, and is available in either single component or three component form with the latter requiring the multi-channel receiver option to be fitted to the terraTEM.
-
product
PXIe-5451, 145 MHz, 16-Bit, 128 MB, PXI Waveform Generator
781204-01
PXIe, 145 MHz, 16-Bit, 128 MB, PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5451 also features advanced synchronization and data streaming capabilities.
-
product
Spring Stiffness Testing Machine
STB Series
Jinan Testing Equipment IE Corporation
STB Computer Control Spring Stiffness Testing Machine Under Axial and Lateral Load is to measure the displacement stiffness of spring under both axial and lateral load, complying with the standard EN13298 Railway applications - Suspension components - Helical suspension springs, steel. The Spring Stiffness Testing Machine measures both axial and lateral stiffness of spring, displacement for both lateral and axial, both loads, offset angle etc. The Spring Stiffness Testing Machine is an ideal testing equipment for spring of chuck and train.
-
product
Portable Gas Analyzer
PG-300 Series
The PG-300 is a compact and lightweight stack gas analyzer that can simultaneously measure up to five separate gas components. Its capability of providing precise measurement has been proven for field measurements and also for laboratory applications. The PG-300 series also offers the capability to measure methane (CH4). A 20% weight reduction over previous PG models and integration of shock-resistant side guards make the PG-300 a robust analyzer for use in the field. An optional electronic cooler unit is available for long-term measurements for severe monitoring applications as gas turbines, boilers, and incinerators PG-300 series versatility makes the analyzers suitable for investigating environmental problems, evaluating catalyst performance, and for controlling process gas streams.
-
product
Oil Tan Delta Tester / Tester System
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
product
Adapter Kit, 3.5 mm to Type-N, DC to 18 GHz
11878A
The Keysight 11878A adapter kit provides the RF components generally required when an SMA or 3.5 mm device needs to be measured with a network analyzer type-N configuration. This kit includes four type-N to 3.5 mm adapters for both male and female connectors.
-
product
Double-deck High and Low Temperature Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Double-deck High and Low Temperature chamber was designed to test battery cell combined with charge and discharge equipment, and also available to thermal test for small products and components.
-
product
Holiday Detector
APS Holiday Detector
800 volts to 35,000 volts in one instrumentSafety cutoff switchDigital output displaySuper bright LED displayTwo volume SettingsRegulated voltageLarge push button controlsGreater battery efficiencyCompatible with Model AP/S1 & AP/S2 components and accessoriesOpen, ergonomic designTHREE YEAR WARRANTY
-
product
AC Test Transformer
Yangzhou Power Electric Co., Ltd
The AC test transformer are especially designed for testing high voltage products and components, such as cables, power transformers, gas-insulated switchgears, bushings and arresters. It is also suitable to test insulation materials. They are used to generate testing high voltage and function as part of the complete system. These systems are particularly suited for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (inductive voltage transformers).
-
product
In-Line Inspection
Mapvision | Q
Inspect ALL features for EACH part you manufature within your Takt time – even for the most complex components with hundreds of features.
