Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
10-CH Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
product
Industrial CANopen And CANopen FD Module For Digital I/O Applications
PCAN-MicroMod FD DR CANopen Digital 1
The PCAN-MicroMod FD DR CANopen Digital 1 is an I/O module for use in CANopen and CANopen FD networks. The modern CANopen FD® standard makes it possible to cope with the constantly increasing need for data transmission from sensors, machines and complex production systems. The module has a CAN FD interface as well as 8 digital inputs and 8 digital outputs. With the DIN rail housing and the support of the extended temperature range, the module is suitable for use in an industrial environment.
-
product
CAN AD MiniModules
CSM’s AD MiniModules of the AD CAN MM (MiniModule)-Series offer a wide range of applications for measuring analogue signals (voltage, current, pressure, flow rate, etc.).
-
product
The PC Link Software For CAN/LIN Data
LE-PC7GX
This PC link software “LE-PC7GX” captures CAN/LIN data into PC measured by the CAN/ LIN optional expansion kit for LE-2500/LE-3500. It also has other functions, such as displaying the specific data at real time (watch data function), maximum 16GB recording function, search function, and text conversion function.
-
product
CAN/Ethernet Gateway
CAN-ETH
CAN-ETH is a CAN to Ethernet gateway specifically designed to interface CAN networks with TCP/IP networks.
-
product
Qseven V1.2 SoM With I.MX287 454 MHz (Industrial) SoC, 128MB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M100
*Ultra low power consumption ARM9*High flexibility Qseven v1.2 compliant design*2 CANBus 2.0B compliant ports*24-bit TTL LCD*Dual 10/100 Base-T Ethernet*Audio
-
product
High-Frequency Generator
ZET 7191
The ZET 7191 is a high-frequency generator on the CAN bus intended for generating high-frequency signals of any shape. The shape of the generated signals may be of two types: sinusoidal and radio impulse.
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
product
Transceiver Module
Mornsun Guangzhou Science & Technology
MORNSUN transceiver modules include integrated high efficiency CAN, RS485, RS232 isolated transceiver module, protocol conversion module and serial port to ethernet transceiver module. These industrial bus transceiver with DIP, SMD, SOIC and DFN optional packages features compact size, surge and ESD bus protection, a maximum isolation voltage up to 5,000 VDC and a wide operating temperature range of -40°C to 85°C, even up to 105°C, etc. Coupled with the use of IC integrated technology, the isolated transceiver module can easily be embedded in the user's end equipment, and achieve fully-functional bus network connectivity and data communication. Check out these isolated transceiver modules with a reasonable price along with high performance and we hope that they are an ideal fit for your application needs.
-
product
4x (1 to 4) +1x (4 to 1) 75 Ohm 2.5GHz Mux
YAV91750
4x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Reflexive
-
product
NI CAN No Termination Cable w/Power Terminals, HS/FD/LS, 2m
782578-02
9-Pin Female D-SUB With 2-Pin Female Power Screw Terminal to 9-Pin Female D-SUB CAN Cable - The DB9F-PT2F-DB9F CAN Cable, sometimes referred to as CAN Cable (with power terminals), connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules that have ports requiring external power with external CAN signals. The screw terminals on the cable allow for the direct wiring of power and ground to the port on the CAN interface. This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals and is available with or without termination.
-
product
FMC I/O Module
FM192
Sundance Multiprocessor Technology Ltd.
The FM192-R board is designed to fan out the FMC-LPC connector I/Os to four DB9 connectors and one SEIC connector. The FM912-R provides wireless connectivity via WiFi + BLE and 4G + GNSS/GPS modules. 3x antenna connectors (2x for the 4G + GNSS/GPS and 1x WiFi + BLE) are provided for connecting 3x external antennas. Furthermore, the FM192-R provides an IMU sensor, CAN BUS, humidity and temperature sensor and Audio I/O.
-
product
Instrumentation System
Reach Technologies has leveraged the success of its automotive instrumentation, and applied it to other industries. The availability of established CAN products, coupled with its robustness, makes CAN a cost effective instrumentation solution. The software back-end of our instrumentation system is comprised of a server to interface to the data loggers, a database server to manage the data, and a web server for control and data visualization.
-
product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
product
Real-time DAWN Mini Streamer™
The DAWN Mini Streamer™ transfers OBD, CAN and J1939 data from a car or heavy duty vehicle to a mobile device (tablet, smart phone or PC) in real-time. Data is transferred using WiFi, so the technician can be in or outside of the vehicle.
-
product
MPOD Micro-2 Crate
The Mpod micro-2 crate is the new small and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod micro-2 mainframe can house up to 2 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
product
I/O Modules
*Configurable input / output functions*Direct connection of hydraulic valves or joysticks*Modules with M12 connector or central plug*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
product
BATTERY PACK AND BMSTEST SYSTEMS
DMC's Battery Pack Test Systems facilitate battery design as well as research and development for national laboratories and research institutions. They are deployed in end of line / production test stations for battery packs developed by major automotive manufacturers and their suppliers. DMC's battery pack test systems are designed to evaluate the battery as a complete system and validate a comprehensive range of battery pack functionalities, including:Power performance, Capacity, DCR / Internal ResistanceContactor and safety interlock functionsIsolation / Insulation ResistancesReporting of operating data through external communication interfaces (usually CAN)Cell VoltagesPack / Cell TemperaturesState of ChargeFaults / Diagnostic Trouble Codes (DTCs)Etc.Electrical characteristics / continuity of internal pack wiring / signalsCooling system operation
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
InfiniiVision Oscilloscopes
2000 X-Series
70 MHz to 200 MHz See more signal detail with 50,000 wfms/s update rateView time-correlated digital content with 8 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, I2C, SPI and RS232/422/485/UART Protect your investment with full upgradability
-
product
80 I/O Multifunction Module
YAV90832
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Ethernet to CAN Bus Gateway
YAV90090
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
8-Ch SPST 20A-250VAC High Current
YAV90087
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
