Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI BRIC8 FIBO Matrix Dual 100x4 3pin brkout
40-592A-105
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
SparkFun FTDI Basic Breakout
3.3V
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
-
product
Universal Breakout Test Fixture
CA-323
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
product
PC Controlled Bench Top Power Analyzer
PA2100
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
-
product
Nano-Pitch Male to Nano-Pitch Male OCuLink x4 Cable, 1 m
785486-01
42-Pin Male Nano-Pitch to 42-Pin Male Nano-Pitch, Shielded OCuLink Cable - The SH42MNano-Pitch-42MNano-Pitch OCuLink Cable, sometimes referred to as OCuLink x4, 1M - Nano-Pitch, connects multisignal DIO connectors on RF and FlexRIO devices to other NI devices or accessories like the SCB-8 breakout connector. The cable acts as a data communication interface and provides access to FPGA multi-gigabit transceivers (MGTs) and/or general-purpose LVCMOS signals from the NI device.
-
product
SparkFun RJ11 Breakout
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the board to match a standard telephone wire. Additionally, each board has pin numbers on the back side that match with the pins on the connector.
-
product
SparkFun Capacitive Touch Breakout
AT42QT1011
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins.
-
product
sbRIO 2mm IDC Connector Breakout
784507-01
50-Pin Male IDC to 66-Pin Female Screw, Breakout for sbRIO Terminal Block - The sbRIO Breakout Box is a 2 mm insulation-displacement contact (IDC) connector breakout that provides easy access to the multifunction I/O and digital I/O connectors on CompactRIO Single-Board Controllers. The connector breakout provides screw-terminal access to the onboard I/O, which eliminates the need to create a custom cable. You can use this accessory at your desk or mount it directly to the controller for an alternative wiring solution during deployment.
-
product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
product
SparkFun Gas Sensor Breakout
This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on every MQ gas sensor product. This is an extremely handy and economical board to have around when detecting multiple types of gases.
-
product
SparkFun USB To Serial Breakout
FT232RL
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
-
product
Breakout Boxes
D Series
The D Series Breakout Boxes incorporate a printed circuit board for all connectivity. D Series Breakout Boxes use a color coding scheme as an aid. The Red jacks connect to the Red TP Side connector with pin contacts and the Black jacks connect to the Black TP Side connector with socket contacts.
-
product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
SparkFun Electret Microphone Breakout
This small breakout board couples an Electret microphone (100Hz--10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V.
-
product
LoRa 1W Breakout
915M30S
Do you need power? This breakout for the 915M30S module from EBYTE is a 1W (30dBm) LoRa transceiver. LoRa is great for long range (miles), low power (in sleep), and low data rates (~500bps). This breakout board is designed to connect to any platform that has SPI and 6 available GPIO. We include a robust edge mount RP-SMA connector to connect large LoRa (915MHz) antennas. In addition, the on-board U.FL connector can be used if you need to get outside a metal enclosure.
-
product
SparkFun 16 Output I/O Expander Breakout
SX1509
Are you low on I/O? No problem! The SX1509 Breakout is a 16-channel GPIO expander with an I2C interface – that means with just two wires, your microcontroller can interface with 16 fully configurable digital input/output pins. But the SX1509 can do so much more than just simple digital pin control. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. This breakout is similar to a multiplexer or "mux," in that it allows you to get more IO from less pins. And, with a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix.
-
product
SparkFun GPS Breakout
XA1110 (Qwiic)
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the XA1110 GPS module from GTOP, this board utilizes the MediaTek MT3333 chipset, loaded with specialized SparkFun firmware that enables both I2C and serial ports simultaneously. Using I2C means you won’t have to tie up your serial port with GPS, leaving it open to other possibilities.
-
product
SHC68-H1X38 High-Speed Digital Flying-Leads Cable Accessory, 1.5m
192681-1R5
76-Pin, Female Flying Leads to 68-Pin, Male VHDCI, Shielded, 50 Ω Digital Cable - The SHC68-H1X38 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments directly to individual header pins for use with a custom breakout fixture. The flying-lead cable has paired signal and ground lines for each channel to preserve signal quality. Each signal and ground line is designed to plug directly into any 0.1 in. header connector. It is a shielded, 50 Ω cable.
-
product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
-
product
EMX-4XXX Product Family
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
SparkFun MicroB USB Breakout
This simple board breaks out a micro-B USB connector's VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B USB to your project, but don't want to put up with soldering the tiny connector, this is the board for you.
-
product
Serial Board
104-COM232-8 Series
This is an eight, four, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports full RS-232 serial communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors for the boards optional breakout cable. The boards are feature-rich and allow for the connection of multiple serial devices—ideal for a variety of applications such as POS, barcode readers, modems, machine monitoring and control, military, high-density networking applications or any other application requiring the connection of RS-232 serial devices to a PC/104 compatible system. Type 16780 UARTS are used as the asynchronous communication elements. These include 64-byte transmit/receive FIFO buffers to protect against lost data in multitasking systems while maintaining 100% compatibility with all operating system COM port drivers. ACCES offers the 104-COM232-8 series in both standard and extended temperature versions ideal for outdoor applications or harsh industrial surroundings. Ordering options include UARTs with larger FIFOs, support for custom baud rates, vertical I/O pins, and custom cabling.
-
product
Air Quality Click
64202
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
PXI BRIC8 FIBO Matrix Dual 20x4 3pin brkout
40-592A-101
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
PXI BRIC4 FIBO Matrix Dual 155x4 2pin brkout
40-592A-115
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
product
SparkFun 2D Barcode Scanner Breakout
The SparkFun 2D Barcode Scanner Breakout is a nifty little breakout board featuring the DE2120 barcode scanner module from DYScan. The DE2120 reads 20 different barcode symbologies (both 1D and 2D) using a camera coupled with on-board image processing to identify and decode everything from UPC codes to QR codes. The module also features two LEDs: one for illumination and one to project the red line that you're used to seeing from laser-based scanners.
