Filter Results By:
Products
Applications
Manufacturers
Antennas
any structure or device used to collect or radiate electromagnetic waves.
See Also: Broadband Antennas, Log Periodic Antennas, Directional Antennas, HF Antennas, Biconical Antennas, Horn Antennas, Isotropic Antennas, Loop Antennas, Antenna Software, Antenna Analyzers, Dipole Antennas, Transmitters, MIMO
- LBA Group, Inc
product
Maritime Navigation and Communications Antennas
LBA provides equipment and services to support shore station requirements for modern maritime communications in the low frequency, medium frequency, and high frequency radio bands
-
product
Active biconical Antennas
BicoLOG X Series
Only a single broadband test antenna for the complete frequency range from 20MHz up to 3GHz. Optimal for usage with spectrum analysers for EMC measurement. Active Antennas with high gain up to 41dBi.
-
product
Precision Conical Dipole
PCD 8250
Exposure evaluation next to mobile communication facilities e.g. GSM and UMTS base stations. Accurate RF radiation safety measurements e.g. nearby broadcast stations or in buildings. All kinds of field strength measurements where high precision, a wide frequency range and small antenna dimensions are required. Measurements according to our Field Nose method. Frequency range: 80 MHz 3 GHz
-
product
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 Module Card with Cables and Antenna Kit
EWK-M2-AC9260
- Bluetooth 5.1- IEEE 802.11ac wave 2 (Wi-Fi 5)- Operating Temperature : 0°C to 70°C (-40°C to 75°C extended)- Compact M.2 2230, A/E key form factor with cable and antenna kit to support flexible installation
-
product
UHF- SATCOM Antenna System
AT-6000
This antenna includes UHF-SATCOM and VHF/ GPS/ GSM/ IFF functionality. It is especially designed to increase the communications capability on vessels and submarines which are limited in number of mast or space. The AT-6000 antenna finds its utilization also in re-fit programs.
-
product
Antenna, Dual Ridge Horn
EM-6963 | 18 GHz – 40 GHz
Model EM-6963 can be individually calibrated for use in EMI/EMC compliance measurements as well as for general purpose measurement antennas over its specified frequency range.
-
product
Logarithmic Periodic Broadband Antennas
Standard LPDA
Is a demountable logarithmic- periodic broadband Antenna (LPDA). For transport and space saving storage, it is delivered with fast links. The fast links allow to demount the rear elements within a few seconds without any tools.
-
product
DC Blocking L-Band Splitter Combiner
PD5920
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5920 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
product
Temperature Stabilized Antenna
TSA-100
A major source of error in timeand frequency receivers is the variationof signal delay due to changes in the outdoor temperature. The designofthe TSA-100 includes two fully independent thermal zones, each with itsown precision heating and cooling capability. The result is that thetemperatureof the preamp is maintained within ±0.5°C over an ambient temperaturerange of -20°C to +50°C. This system virtually eliminates bothseasonal and diurnal variations, supporting exceptionalrepeatability.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP6T
87106R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106R is a low PIM SP6T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Range-Doppler Target Generators
ATG9100
The ATG-9100 is an example of a laboratory-quality instrument that will simulate complex target motion. Microwave signals from the speed camera enter the instrument through an integrated antenna which is then downconverted and digitized. Target simulation data is added to the digitized signal to provide range and Doppler information. The modified digital data is then converted back to an IF and upconverted to the original microwave frequency of the speed camera and radiated back through the antenna. Since the ATG-9100 can be phase-locked to an external 10 MHz reference standard, this instrument is suitable for use as a calibration standard for speed cameras.
-
product
Module Spectrum
nRF52805 Series
Raytac nRF52805 tiny and low cost modules spectrum covers MDBT42TV-192K & MDBT42TV-P192K series with both Chip Antenna and PCB Antenna option for selection
-
product
Internet of Things (IoT)
When an IoT device is being designed, it’s important to consider the antenna in relation to the housing and environment. It can seem intimidating, but antenna design doesn’t need to be daunting. With the large increase of wireless IoT devices connecting our world, understanding IoT antenna design is even more important than ever. That’s why we gathered some of our best resources for IoT designers ranging from application notes to eBooks from Microwave Journal.
-
product
Standard Gain Horn Antenna
SAS-586
This Standard Gain Horn Antenna will provide reliable, repeatable measurements. An ideal solution and a standard workhorse of any EMC test house for compliance testing. Features: 12.4 GHz to 18 GHz, Individually Calibrated, FCC, MIL-STD, VDE and TEMPEST Testing.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Helix Antennas
CAES Helix Antennas are designed with over 60 years of antenna design expertise. Available in both normal and axial modes, CAES Helix Antennas are standard equipment on electronic warfare systems worldwide and deliver the performance required for today’s most demanding defense applications.
-
product
VHF Antennas
From small craft to large ships, Shakespeare® VHF antennas are the go-to antennas to keep you connected utilizing the essential VHF marine radio.
-
product
Antenna, Active Loop
EM-6869 | 9 KHz – 50 MHz
The Electro-Metrics EM-6869 Active Loop Antenna is used with any receiver or spectrum analyzer with 50 ohm input and covers the frequency range of 9 kHz to 50 MHz.
-
product
WiFi, Bluetooth, & BLE Antennas
Our wide selection of internal and external Wifi antennas and Bluetooth antennas enable connectivity for multiple devices in nearly any location.
-
product
PIM Analyzers
A form of intermodulation distortion that occurs in components normally thought of as linear, such as cables, connectors and antennas. However, when subject to the high RF powers found in cellular systems, these devices can generate intermodulation signals at –80 dBm or higher.
-
product
External Antennas
As the name suggests, are antennas mounted outside of electronic devices or structures to enhance wireless communication. They are a vital component in various applications, including cellular networks, Wi-Fi routers, satellite communication, and more.
-
product
DC Blocking L-Band Splitter Combiner
PD5960
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
product
Packaged Direction Finding Systems
Doppler Systems offers packaged systems allowing for easy installation and use our radio direction finding systems. The packaged systems include a direction finding processor, an FM receiver, power distribution, a data interface to configure the system and obtain data from the system, and an appropriate antenna or antennas. Additionally, some customers require wireless networking to connect fixed and/or mobile sites together to share data. We also can provide laptop computers with our systems fully configured to interface with the direction finder and run our software.
-
product
Vector Network Analyzer Extenders
VNAX
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
product
Scalar Feed Horn Antennas
Scalar feed horns are offered as both standard and custom build models with either a circular or rectangular waveguide interface. While scalar feed horns with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. The standard models operate across the full waveguide band and offer 17 dBi nominal gain, 25 degrees half power beamwidth and a -28 dB side lobe level at center frequency. The below standard offering covers the frequency range of 8.5 to 140 GHz. However, other frequencies or gain values are also available.
-
product
Receiver
vLoc3-Pro
The vLoc3-Pro utility locator introduces new innovative tools for locating buried utilities assuring damage prevention while gathering information for analysis. With two sets of screened 3D antennas signal distortion is easily detected and displayed on the bright full color display. Along with classic locate screens the vLoc3 series locators offer new locate perspective screens of Vector Locate for fully automatic non-walk over locating, Transverse Graph showing both peak and null simultaneously providing immediate measurement of signal distortion, Plan View showing the relative orientation of the cable at any angle, and a new graphical Sonde screen with guidance arrows leading to the sonde location even when it is vertical.
-
product
Near Field Probes
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
product
DVB-T Omnidirectional Antenna
The COMM-connect DVB-T Omnidirectional Antenna offers superior performance in applications requiring bandwidth in all directions. The antenna comes fully equipped with stainless steel mast brackets & 7/16 female connector, which makes it very easy to install in any type of installation. Our Antenna is housed in a very rugged radome, able to withstand very harsh weather conditions.
