Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
AMP HOUND 2
AMP2
*Attach adapter to fuse or touch probes to top of the fuse to measure automotive amperage instantly without removing the fuse*Audible tone lets you know when you have connection with a fuse and if there is current present in the circuit; perfect for working on under-the-dash fuse boxes*Snapshot Mode and Tracking Mode allow easy component testing and parasitic drain location
-
product
PXI 2A Multiplexer, 1-Bank, 32-Channel 4-Pole
40-614-017
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
PCI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
50-635A-003
The 50-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PXI 2 Amp Multiplexer, 1-Bank, 64-Channel, 1-Pole
40-657A-001-1/64/1
The 40-657A-001-1/64/1 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
PXI Solid State Multiplexer, 10 Amp, Single 6-Channel
40-666A-012
The 40-666A-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Man in the Middle Cable
MitM
The Man-in-the-Middle Cable (Catalog No. MitM) was created to work with the T4000 and T4350 to enable a technician to use an electric vehicle rather than a very large load emulator to absorb the energy delivered by the DC fast charger during charger testing. It currently comes in 350 Amp CCSI and 200 Amp Tesla/NACS models, each with charging connector holders and digital temperature sensors.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PCI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
50-635A-109
The 50-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
IP-QuadUART
IP Module with quad UART capability. 128 byte FIFOs, 8 & 32 MHz operation, RS232 and RS422/RS485 interface, programmable terminations, 1.5MHz - 100 Hz.
-
product
PXI/PXIe Power Relay Module,5 Amp, 50-Pin SGMC Connectors
40-158-001-HI
The 40/42-158-001-HI is a PXI/PXIe high density power relay module with 32xSPDT switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock.
-
product
130 AMP Battery Load Tester
MD4370
Compact, ergonomically designed tester determines a battery's charge and tests batteries, starting, and charging systems.Powerful 130 amp load capacity provides more accurate test results.Uniquely designed clamps assure a positive connection on any style battery.
-
product
Low-Density PXI Multiplexer Switch Modules
Pickering's range of low-density PXI multiplexer switch modules are ideal for applications requiring a lower number of channels and poles. All modules are based on high quality ruthenium reed relays that switch up to 150V, 1.2 Amp with 20W max power or high quality electro-mechanical relays (EMR) that switch up to 300V, 2 Amp with 60W max power.
-
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 37-Pin D-type Connector
42-158-104
The 40/42-158-104 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 37-pin D-type male connector.
-
product
Heavy Duty Vibration Monitor
VUM-800
Features • Heavy-duty sensing probe • DPDT 10 amp relay • Optional 230 VAC operation • Control unit remotely mounted • Failsafe operation
-
product
PCI Matrix Cards
PCI Matrix cards are available in the following:*Reed relay based matrices available in 22x4, 22x8, 44x4 or dual 20x4 formats with 1-pole, 2-pole or 1-pole screened relays*2 Amp electro-mechanical relay based 1-pole matrices available in 32x2, 32x4, 16x4, 16x8 or 8x8 formats.*Select modules are supplied with our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 0.5m, 250 Port
A500RMR-C-4B050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
AC Line Separators
ALS-2
Standard Electric Works Co., Ltd
● x10 Model allows for more accurate measurements of low amperage devices.● Direct reading x1 mode.● 4mm Voltmeter input jacks.● Intergrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
80 AMP FUSE BUDDY TESTER
FB315
*Tests circuit current from 0 to 80A*Includes 20A maxi fuse for use with mini and ATC circuit testing*Resolution: .1A (100 mA)
-
product
Micro Power, Contact, ITA, 21 Amp, 12-14 AWG
610143101
Primary mating contact 610142101. (May mate with other Receiver contacts, as well.)Specifications Operating Current 21 amps continuousContact Resistance 1.5 mOhms max.Dielectric Withstanding Voltage (DWV) 1500 VDC min.Contact Body BrassContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 10,000 cyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.23u
-
product
Hand-Held 12 Volt Combo Digital Load Tester
6028DL
• 60 Amp load to test smaller batteries: CCA and Amp hours• 125 Amp load to fully test larger batteries: CCA and Amp hours• 125 Amp clamps offer greater flexibility when attaching the hard to reach applications • Made in USA of US and Global Components
-
product
Surge / DC Hi-Pot Consoles
HC Model
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
product
Differential Pressure Transmitter
636D
The Series 636D Differential Pressure Transmitter can be used for measuring pressures of liquids, gases & vapors. All available ranges have an excellent 0.5% F.S. accuracy with a 4-20 mA Output standard or optional 1-5 VDC output.
-
product
PXI 16 x DPST Reed Relay 2 Amp
40-136-112
The 40-136-112 16xDPST reed relay module is part of our range of medium power, general purpose relay modules which are capable of switching voltages up to 200V and current up to 2A.
-
product
Dual Channel 100MHz Oscilloscope
GOS-6112/ 6103/ 6103C
100 MHz, Dual Channel, Delayed Sweep. Built-in 6 Digit Universal Counter (GOS-6103C). 10 Sets Memory for Front Panel Setting Save & Recall (GOS-6103/GOS-6103C). Time Base Auto-range (GOS-6103/GOS-6103C). Cursor Readout with 7 Measurements. Panel Setup Lock of Digital-Control Functions. Buzzer Alarm. LED Indicators
-
product
Dual 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-002
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
-
product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Hall Effect Gear Tooth Sensors and Custom-Made Target Wheels
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect Gear Tooth sensors (CYGTS101DC, CYGTS99, CYGTS211, CYGTS212, CYGTS99-198 etc.) for speed measurement with applications to machines, equipments, motorcycles, automobile industry and instruments etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
product
PXI/PXIe Power Relay Module, 2xSP4T, 20 Amp
42-166-202
The 40/42-166-202 is a PXI/PXIe high density power relay module with 2xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
