Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI Chassis
Our LXI chassis allow any of our 3U PXI switch modules and many of our instrumentation modules to be controlled in an Ethernet environment. You may also be interested in our 2-Slot USB/LXI Chassis, this chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. Also our 4-Slot USB/LXI Chassis allow USB or Ethernet control of most PXI modules up to 4-slot width. For more information on these chassis, you can look in the bottom part of the table below.
-
product
USB⇔RS-422/RS-485 Conversion
SI-35USB-2
SI-35USB-2 is an USB converter, which converts USB of PC into RS-422/RS-485.
-
product
USB Modular Oscilloscope, 200 MHz, 2 Analog Channels
U2702A
200 MHz2 analog channelsMore accurate analysis of electronic designs with deep 32 Mpts memory and high 1 GSa/s sample rateSimplify your setup with USB plug and play capabilityGet the debug power you need with advanced triggering, automatic measurements, math functions including FFTs and moreQuick and easy measurement configuration and acquisition with bundled Keysight Measurement Manager (KMM) software
-
product
1GS/s 75MHz BW USB Modular Scope Pen
USBscope50
USBscope50 marks a new era in ultra portable modular instrumentation for the PC or notebook. Using a USB1.1 or USB2.0 port on the host computer, USBscope50 offers the best of all worlds for converting your PC into a powerful diagnostic tool: tiny size, low power, low cost, modularity and high performance.
-
product
Thermo-Hygrometer
S3631
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
product
Industrial Mini-ITX Motherboard With 14/13/12th Gen Intel® Core™ I9/i7/i5/i3 Processors
AmITX-RL-I
- 14/13/12th Gen Intel® Core™ i9/i7/i5/i3 processors and Q670 chipset, up to 65W- Dual-channel DDR5 4800 MHz memory up to 64 GB- Quad. independent display: HDMI 2.0b, HDMI 1.4b, DP 1.4a, LVDS or eDP- Dual GbE ports: 1x 1GbE, 1x 2.5GbE- Expansion slots: 1x PCIe x16, 4x USB 3.2 Gen2, 2x USB 3.2 Gen1, 4x USB 2.0, 1x M.2 B-key, 1x M.2 E-key, 2x M.2 M-key- Support ATX (24+4 pin) or 12V DC-in power input
-
product
HandyScope HS6-DIFF With SafeGround With SafeGround & SureConnect
HS6-DIFF-100XMSG-W5
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
product
Electrical Safety Test Scanner
19200
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
product
30MHz Arbitrary Waveform Signal Generator
Model AWG30D
- 4.3′ High Resolution TFT LCD Display- Two Independent Channels Output, Same Characteristic- 1μHz Frequency Resolution for whole range- 120 MSa/s Sampling Rate, 14 Bits Vertical Resolution- 5 Standard Waveforms, 50 Built-in and 5 User-defined Arbitrary Waveforms- FM, AM, PM, PWM, Sum, FSK, BPSK and SUM Modulation, Sweep and Burst Function- Channel Coupling and Combine Features On CHB- Build in 350MHz Frequency Counter- Arbitrary Waveform Edit PC Software- Standard Interface: USB Host, USB Device and RS-232
-
product
SparkFun FTDI Basic Breakout
3.3V
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
product
PICMG 1.3 Half-size CPU Card With LGA1150 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q87, SATA3, USB 3.0, DVI-I/LVDS And Dual LANs
SHB230
The SHB230 is high-performing PICMG 1.3 half-size single board computer.The SHB230 based on the Intel® Q87 PCH is designed to support 4th Generation Intel® Core™ i7/i5/i3 and Celeron® processors (codename: Haswell/Haswell Refresh) in the LGA1150 socket.The slot CPU card is equipped with two DDR3-1333/1600 SO-DIMM sockets with up to 16 GB memory capacity to meet customers needs.The PICMG 1.3 specification brings advantages of PCI Express to this single board computer that offers four PCIe x1 or one PCIe x4, and one PCIe x16 routed to the backplane.The onboard two SATA interfaces support RAID 0/1 functions to ensure reliable storage for multiple applications.Utilizing with the latest Intel® technologies, this PICMG 1.3 system host board is an ideal solution for DVR, medical equipment, industrial automation, process control, and network security market.
-
product
DataNet Wireless Data Loggers
The DataNet wireless system is a data acquisition solution developed for 24/7 real-time monitoring for mission critical organizations. Boasting a variety of wireless data logger models using ZigBee RF technology, the DataNet solution is capable of measuring parameters such as temperature, relative humidity, voltage, current, or frequency. Choose from DataNet models offering up to 6 inputs or the more cost-effective single or dual input Mini DataNet range, depending on your application requirements. Each DataNet mesh network is managed by a Receiver connected via USB to a Windows-based PC, and also supports addition of wireless Repeater units for extending the network transmission range and improving network robustness.
-
product
High Power DC Electronic Load
34000A Series（5KW~40KW）
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
Handheld Laser Power & Energy Meter
Nova ΙΙ 7Z01550
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors.*Large, high definition LCD display.*Both digital and analog needle display.*USB and RS232 output to PC with Statistics package.*Select between English and Japanese interfaces*Analog output.*Soft keys and menu driven functions with on line help.*Log every data point at up to 4000Hz with pyroelectric sensors.*Non-volatile data storage up to 59,400 points.*Laser tuning screen and power log.*2 position kickstand.*System Integrator Tools included: LabVIEW VIs, COM Object Interface.
-
product
Resistance System - Digital Surface Resistance Meter up to 200 TeraOhms
PRS-801B
- Accurate Wide Range Resistance Measurements: 0.01 Ω to 2.00x1014 Ω- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Variable Voltage 0.1 mv to 9.99 V for low resistance measurements- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Auto Resistance Range Control- Auto Test Voltage Control- Uses a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- 999 Data Set Memory- Download to Excel® in Batches or Individual Measurements with Prostat Connect 2.0- Uses Micro USB Cable for Charging and Downloading Data- Charges in 2 Hours- 2-year Limited Warranty on Main Instrument
-
product
DMX Tester
DMXter4 RDM
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
product
ZonuSkyShot GPS Tester
The ZonuSkyShot GPS Tester is a compact GPS receiver which detects the presence and, the signal strength of a GPS signal, and identifies all the satellites “seen” carried by the signal. The device enables laptop or phone connectivity to report and indicate this at the LED device’s screen. Furthermore this GPS receiver can be accessed at the USB port on the Base Unit, or via a Bluetooth™ device allowing the user to see the available satellites using the app provided with the system.
-
product
*OEM Power Sensors
The OEM “standard” sensors are actually families of existing OEM sensors with typical specifications shown. They can be tailored as needed to fit your specific requirements. In addition to the products described, Ophir has developed hundreds of other OEM solutions. These compact laser power sensors have built-in amplifiers and are easy to install. They contain all the electronics needed including algorithms to increase the sensor's speed of response. Connections to the sensors are simple, with the host providing DC power and the sensor providing a voltage or digital output. Outputs Available: DB15 smart sensor output; Calibrated analog output; RS232; USB; Ehthernet. Simply fill out the Sensor Customization form so we can provide just the right solution for your needs.
-
product
Optical MultiTest Platform
AP1000-8
The AP1000-8 can accept up to 8 plug-in modules. These Plug-in modules are automatically recognized after insertion. The user can control the equipment with the 5.7 inch sensitive screen or with a mouse and a keyboard (three USB ports are available on the front panel). An internal memory is available and measurements, grids and setups can be saved/loaded in .txt format. The user can take the control and perform data transfer with a computer through GPIB or ethernet. It is also possible to take the control of the equipment through the internet from anywhere in the world. Optionaly, a trigger synchronized with the Optical Tunable Laser Sources modules can be added.
-
product
Static Tester for Lab and Workshop
ADSE 715 RS
The ADSE 715 is a complete high performance single pressure Ps stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air data computers ) and sensors. The high precision embedded sensors enable the ADSE 715 to be used as a pressure standard. The user interface running on a PC connected through USB link is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
product
Raspberry Pi Zero w/ Wireless LAN & Bluetooth
Raspberry Pi Zero W
Full feature list for Zero W: 1GHz, single-core CPU. 512MB RAM. Mini-HDMI port. Micro-USB On-The-Go port. Micro-USB power. HAT-compatible 40-pin header. Composite video and reset headers. CSI camera connector. 802.11n wireless LAN. Bluetooth 4.0. We imagine you’ll find all sorts of uses for Zero W. It makes a better general-purpose computer because you’re less likely to need a hub: if you’re using Bluetooth peripherals you might well end up with nothing at all plugged into the USB port. And of course it’s a great platform for experimenting with IoT applications.
-
product
High-Speed 4-TAP USB 2.0 JTAG Controller
USB-1149.1/4E
The USB-1149.1/4E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/4E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
Economical 4U Rack Mounted Industrial Chassis Supports ATX Industrial Motherboard
RK-620MB-L Series
- Supports ATX industrial motherboards- Two external 5.25'' drive bays- Two USB type A connectors on front panel- 12cm two ball bearing cooling fan ( 103 CFM)- PS2 ATX power supply
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Integrated Potentiostat and Multiplexer
EmStatMUX8
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
product
Spectrographs & Monochromators
Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. More than 100 gratings for the best spectral range, throughput and dispersion to meet your applicationDSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioningOptional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuationInstallation and set-up through USB 2.0 computer interfaces Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programsZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up
-
product
Fanless Embedded System With Intel® Atom™ Processor E3845 Quad Core™ (1.91 GHz) For Railway PC
tBOX323-835-FL
The tBOX323-835-FL, a fanless railway PC, is designed for in-train applications. Integrated with onboard quad-core Intel® Atom™ E3845 processor and 4 GB low-powered DDR3L memory. The fanless railway PC boosts its computing performance and specializes its I/O design with five isolated COM ports, two M12-type LAN connectors, USB 2.0 ports, and one isolated digital I/O. The railway PC also provides VGA and HDMI outputs for in-train surveillance. The tBOX323-835-FL is an ideal all-in-one IoT (Internet of Things) solution for various applications, including railway multi-functions of gateway, controller, digital signage management and surveillance. Certificated with EN50155 and EN50121 for rolling stock and complied with EN45545-2 for fire resistance, the rugged embedded system operates reliably in a -40ºC to 70ºC operating temperature range (EN50155 Class TX) and in a high vibration environment.
