Filter Results By:
Products
Applications
Manufacturers
Wind Tunnels
deliver specific air-stream to characterize air-flow's affect.
See Also: Wind, Tunnel, Anemometers, Wind Turbine, Wind Speed
-
-
product
Ruggedized Ethernet Data Acquisition Systems
Series 7000
The Series 7000 Ruggedized Ethernet DAS brings new capabilities and levels of performance to transducer data acquisition. The ruggedized system is designed for installation in wind tunnels, engine test stands and other facilities where it is desired to locate the DAS on or near the test article, reducing installation and cable costs while improving signal quality and reliability. Each unit is a network appliance which conditions, amplifies and digitizes outputs from transducers. Multiple units are easily combined and distributable for larger installations. Real-time temperature Compensation of gain offset and Excitation Voltage, quality signal conditioning with high gain and a 24-Bit A/D per channel provide a high accuracy and high resolution DAS that will perform across a wide operating range.
-
product
Micromanometers
The DPM range of handheld auto-zeroing Micromanometers are renowned in the HVAC, aerodynamics, clean room, wind tunnel, COSHH, LEV sectors and in other industries where low pressure measurements are critical.
-
product
Wind Sensor
FT722
Specifically designed for wind turbine control, the FT722 reads wind speeds from 0-50m/s. Its inovative design incorperates a series of "turbulators" (patient pending) which condition the air flow. With updated software, and calibration in our new state-of-the-art wind tunnel, the FT722 delivers our highest levels of accuracy in wind speed, wind direction and accoustic temperature measurement.
-
product
Wind Tunnels
Omega's Wind Tunnels come in benchtop or floor standing models for any research, manufacturing, or quality control application. All Wind Tunnels are manufactured in The USA.
-
product
Aerospace Testing Solutions
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
product
Wind Tunnel Control System
WTCS
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
product
Wind Tunnel Balances
To meet the increasing demands of a modern wind tunnel and the need for appropriate simulation, HORIBA has developed the rolling road and wheel spinning units for road simulation. To increase the wind tunnel efficiency, the HORIBA wind tunnel balances can be equipped with lifting platforms which enable vehicle modifications to be performed in a short time
-
product
Semiconductor Package Wind Tunnel
WT-100
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
product
Integrated Solutions
Sensor Signal Conditioning with embedded wideband Data Recording in a compact chassis for structures laboratories, engine test cells, wind tunnels and other computer-processed measurements of physical phenomenon: strain, vibration, pressure, temperature, flow, etc.
-
product
Wind Sensors
FT742
The FT742 measures wind speeds up to 75 m/s. Its innovative design incorporates a series of “turbulators” which condition the air flow to deliver our highest levels of accuracy yet. Available in four mounting options, the Flat Front (FF) and Pipe Mount (PM) are typically used in wind turbine control and the Direct Mount (DM) in meteorological applications. The Surface Mount (SM) has been specifically designed for OEM integration and for use on UAVs/drones.
-
product
Wind Sensors
FT702
The current version of the FT702 is Version 22. Its strength and dependability have made it particularly popular for wind turbine control. It is used globally by the world's leading wind turbine manufacturers, as well as in a range of meteorology applications.
-
product
Wind Power Solution
ECO SUZLON
The ECO SUZLON is custom-made with firmware and fixtures designed specifically for Suzlon turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
-
product
Pocket Wind Meter
Kestrel 2000
The Kestrel 2000 Pocket Weather Meter is the most elementary temperature and wind monitor in the Kestrel Meter collection. Capable of measuring both wind and temperature phenomena, the Kestrel 2000 Thermo Anemometer is a compact and durable weather meter that puts essential weather information in the palm of your hand
-
product
Wind Power Solution
NXA GAMESA
The NXA GAMESA is custom-made with firmware and fixtures designed specifically for Gamesa turbines: G80x, G90x, G114, G126, G132, G145. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Wind Meter Base Model
Kestrel 1000
The Kestrel 1000 Wind Meter is the base model in our extensive assortment of Kestrel pocket weather meters. Simple and compact, the Kestrel 1000 fits right into the palm of your hand and weighs a mere 65 grams. It's also extremely durable and totally waterproof, allowing you to measure wind speeds in even the harshest weather conditions. It even floats.
-
product
Wind Power Solution
EVO ACCIONA
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Tunnel Demagnetizing Unit
DM-T
Tunnel units are particularly suited to demagnetising parts with large surface areas and thin walls, for example, tubes, rods, etc.
-
product
Wind Power Solution
ECO GE
The ECO GE is custom-made with firmware and fixtures designed specifically for GE 1.5x and 2.5x. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Wind Power Solution
ECO MITSUBISHI
The ECO MITSUBISHI is custom-made with firmware and fixtures designed specifically for Mitsubishi turbines: 1000, 1000A, MWT 2.4. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
Wind Speed and Wind Direction Sensors
Wind vanes measure wind direction and are often used with anemometers, which measure wind speed. Campbell Scientific offers a variety of anemometer designs: cup, propeller, ultrasonic, sonic, and lidar. Most of our wind sensors are modified slightly from the manufacturers’ stock items so that they may be used with our dataloggers in research, air quality, and general purpose meteorological applications.
-
product
Dual Mode Wind Turbine Performance Lidar
ZephIR DM
ZephIR DM is a Dual Mode variation of the successful 300 system. ZephIR DM measures wind characteristics in front of or behind a turbine from just 10 metres (33 feet) out to 300 metres (984 feet) situated inside the spinner or on top of the nacelle, during the operation of wind farms onshore and offshore (this is limited to 200m (656 feet) when in ground based vertical mode).
-
product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
product
Wind Turbine Condition Monitoring
It has also become increasingly apparent in recent years that the wind turbine industry has recognised the importance of condition-based monitoring, especially for offshore wind turbines, where access is often limited.To increase reliability and minimise down time, many wind turbine manufacturers, owners and operators are turning to condition-based monitoring systems, aimed at predicting wind turbine maintenance issues, so that operators can quickly and effectively carry out predictive maintenance, repairs and replacements of components when needed, without the need for costly routine maintenance checks and visits. As a result, a condition monitoring system increases operational time, improves site performance and reduces maintenance costs for wind turbines, especially offshore ones.
-
product
Ultrasonic Wind System
UWS
Aeronautical & General Instruments Ltd.
Data from the mast-mounted (and virtually maintenance-free) anemometers is processed and used to drive full colour displays. The system calculates cross winds, head winds and tail winds, gusts and lulls and directional variation, as well as allowing for marked discontinuities. Instantaneous data may be displayed, as well as 2 minute and 10 minute averages. Systems can be supplied fully installed with comprehensive engineering and operator training, and post-installation support is available worldwide.
-
product
Wind Measurement and Meteorological System
Moriah
Aeronautical & General Instruments Ltd.
MWS is a solid-state system with no moving parts, so providing a highly accurate, reliable and low cost of ownership system, which is ideal for supporting ship based aviation activities. The system comprises of 1 to 5 Solid State Wind Sensors, Dual Redundant Processor Unit, a range of Multi-Function Color Displays (8.4”, 10.4” and 15.0”) and utility Software/Graphic User Interfaces. In addition full Meteorological capability can be achieved with the inclusion of Air Temperature & Humidity, Air Pressure and Sea Temperature Sensors.
-
product
Wind Transmitters
Comptus wind speed and direction transmitters convert the sensor signals into electrical outputs suitable for connection to displays, computers, dataloggers, wireless transmitters, or other controls. Output options include: 0-1 mA, 0-1 V, 0--5 V or 4-20 mA. Power options include: 24 VAC, 120VAC, 230VAC, 12-24 VDC. Comptus transmitters come standard in a track mount for installation in existing enclosures. They are also available in NEMA rated enclosures. Please contact us for enclosure options.
-
product
Wind Profilers
Bristol Industrial & Research Associates Ltd
Biral provides Sodar systems for the 3-dimensional measurement of wind speed and direction in a vertical column extending hundreds of metres above the sensor. Sodar systems are used in applications such as wind energy site assessment, wind shear detection at airports, plume modelling and basic research.
-
product
Wind Direction Sensor
ENVIROMUX-EWDS
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
