Filter Results By:
Products
Applications
Manufacturers
- LBA Group, Inc
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Tape Up and Down Conversion Board
LS-37-P
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
product
Standalone Media Converters
Advantech's standalone media converter facilitates cabling with simple conversion and optional internal power security device.
-
product
2 to 8 Channel Anti-Alias Low-Pass Filter Card
AAF-1
The AAF-1 is a multi-channel anti-alias low-pass filter board designed for front-end signal conditioning in PC-based or stand-alone 12-bit A/D conversion systems.
-
product
3-CH RTD Input Module
ND-6013
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
High Speed ADC > 10MSPS
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include high IF ADCs (10 MSPS to 125 MSPS), low IF ADCs (125 MSPS to 1 GSPS), integrated receivers, and wideband ADCs (>1 GSPS). The High speed ADC portfolio offers solutions for all high speed conversion applications.
-
product
Electric Vehicle Test Solution
As the automotive industry advances power conversion and battery technologies, Chroma has been actively working to improve electric vehicle (EV) testing performance and cost by developing flexible automated power conversion test platforms and regenerative battery test systems. Chroma ATE is a world leading manufacturer of precision test and measurement instrumentation, automated test systems, intelligent manufacturing systems, and turnkey test and automation solutions. Chroma’s Automated Test Systems for Electric and Hybrid Electric Vehicles consist of standard test platforms that are combined into one expandable test system that can test most power components in an EV’s power system. Compared to specialized test equipment developed for a single EV model or application, Chroma’s systems provide greater flexibility.
-
product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Reference Grade Expandable Production Interface
Atlas
Atlas and Titan are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Atlas provides more preamps than Titan making it suitable for a wider range of recording scenarios.
-
product
Modbus Register Converter
Model 2390
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
product
20 GHz Signal Source
VCO Series
The SC5510A and SC5511A are VCO-based, synthesized signal sources with very low phase noise and an amplitude control of 0.01 dB throughout its -30 dBm to +15 dBm output power range. By utilizing a unique multiple phase-locked loop architecture, phase spurs are kept below -70 dBc across the entire tuning range, even at 1 Hz step resolution. Download the data sheet to see how the impressive features and specifications of these modules make them stand out when compared to other small modular synthesizers. These 20 GHz signal sources include an additional, independent RF2 channel with a tunable frequency range from 100 MHz to 3 GHz and a tuning resolution of 25 MHz. The extra channel makes the modules suitable for either single-stage RF conversion systems or dual-stage image suppression up/down converter systems. Both modules make great general-purpose laboratory signal sources where demanding low phase noise and signal purity are required. They are both ideal choices as an integrated clock source for fast DAC and ADC applications, especially those that require variable sampling rates. Full implementation instructions, GUI, driver software, and example code are provided with each module.
-
product
Cross Browser Testing
Today’s proliferation of devices and browsers means your user or customer base is highly fragmented and no assumptions can be made about the platforms being used. Through cross browser testing, also known as compatibility testing, Digivante helps you to uncover issues that might block conversion before your users do.
-
product
Airborne Receiver
MS 2015
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
product
Digital Receiver XMC
XF07-518
Curtiss-Wright Defense Solutions
The XF07-518 is a rugged quad channel 500MSPS 14-bit digital receiver XMC. The ADC devices are controlled by a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms.
-
product
LXI Wired Trigger Bus Adaptors And Accessories
We manufacture LXI Wired Trigger Bus adaptors and accessories. These adaptors and accessories are designed to help debug a WTB system or provide conversion of signals to or from the WTB to products that do not support the WTB. LXI approved WTB cable assemblies and terminators are available to interconnect LXI devices that support the LXI Wired Trigger Bus extended function.
-
product
Uninterruptible Power System
GT Series
The Global Uninterruptible Power System or GT Series, features Clary's On-Line Double Conversion technology, and is Power Factor Corrected for a wide range of voltage inputs, (120Vac through 240Vac and 50/60Hz).
-
product
GPIB-RS232, Instrument Control Device - Korea 220VAC
779732-09
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Conversion Devices and Adapters
Conversion devices and adapters fulfill several roles. For example, you can use them to convert an output signal to a signal type that can be measured by a data logger, to adjust resistive bridge measurements, or to build distributed measurement networks.
-
product
Temperature Transmitters
Conversion of Thermocouple, RTD, millivolt and resistance signals from field sensors is accomplished using DEVAR two wire signal transmitters.
-
product
Mezzanine System
5147
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
product
Synchro to Digital-Resolver to Digital Converters
MRDC
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
product
Power Conditioner
ACT2500 Series
Acumentrics continues to provide innovative, rugged, reliable power solutions with the introduction of the ACT2500 Power Conditioner. This durable and versatile power conditioning system contains advanced double on-line conversion to provide power conditioning for electronic devices, meeting the rigorous needs of soldiers operating around the world. The ACT2500 "Vetronics" ready design makes it perfect for combat vehicles including the JLVT, FMTV and HMMWV along with any other application that relies on 28VDC as a source of power.
-
product
Digital Superficial Rockwell Hardness Tester Tallboy
900-349
This digital Superficial Rockwell hardness tester with fully automated load/unload procedures affords highly sensitive and accurate readings. Micro computer controlled with USB output to built-in mini printer or PC. The 900-349 digital superficial Rockwell hardness tester offers programmable scale conversions, dwell times, statistical capabilities and test counter. Capable of testing in all of the superficial Rockwell® scales.
-
product
Scalers & Converters
Down convert VGA, HD-SDI, HDMI, and DVI computer video signals to a composite video signal Industry-leading multi-resolution and multi-format signal conversion and scaling products for Pro AV systems.
-
product
Sixteen Channel 12-Bit Analog Input/Output Cards
PCI-A12-16A
Model PCI-A12-16A is a multifunction, analog-to-digital, digital-to-analog, and digital I/O card. It accepts up to 16 single-ended inputs or eight differential inputs. Inputs are protected against over-voltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts. Conversions can be initiated in any one of three ways: (a) software command, (b) external start commands, or (c) on a timed basis using on-board programmable counters. Converted data may be transferred to the computer by one of two software selected methods: (a) polling for the end-of-conversion signal, or (b) by generating an Interrupt when the end-of-conversion signal occurs.
-
product
16 Channel ADC for CompactPCI
CPCI392
The CPCI392 16-Channel Common-Mode Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
product
Mixers
Teledyne Microwave Solutions (TMS) offer a wide range of both double & triple balanced mixers for many different applications from commercial test equipment to space qualified units. Low conversion loss and wide bandwidths are the hallmark of the product line. The incorporation of Schottky diodes on some designs offers significant performance benefits.
-
product
Power Supply
VITA, VPX, VME, cPCI
PCI-Systems Inc. intelligent power supplies integrate a microcontroller (MCU) for a fully programmable and flexible solution. Intelligent power conversion allows configuration and reconfiguration for different applications. With intelligent power conversion, the power supply becomes a platform solution for many different applications. The power supply can easily be reprogrammed to support different operating limits and control inputs.
