Filter Results By:
Products
Applications
Manufacturers
CW
Wave having a constant amplitude and frequency.
- Applied Instruments, Inc.
product
CATV Multi-Carrier Generator
1685
The Model 1685 is a headend / hubsite RF eight carrier generator. Each CW carrier can be activated individually or simultaneously. The RF carriers generated are extremely clean and stable, thus making the 1685 an ideal instrument for testing/aligning the CATV forward band.
-
product
Coaxial Power Dividers
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
-
product
Ultra-Stable, High-Power, CW Laser in the UV & Visible
SolsTiS Titan
SolsTiS Titan is based on M Squared’s award-winning SolsTiS CW Ti:Sapphire laser platform. It’s a fully-automated, high-power, single-frequency laser operating in the UV and Visible and offers unprecedented stability and reliability. Titan is simple to operate and integrate into diverse industrial and deep-tech application scenarios and delivers dramatic cost savings over legacy laser technologies.
-
product
Power Sensors
RTP5540
Providing the highest video bandwidth and fastest rise times, the 50 MHz to 40 GHz Power Sensor by Boonton is the ideal instrument for fast, accurate and reliable RF power measurements. This module is ideal for many different applications including Crest Factor and Peak to Average Power Ratio (PAPR) measurements for Power Amplifiers and RF components; Telecommunication & Satellite signals: W-CDMA, QAM, OFDM, LTE-FDD and LTE-TDD; WiFi signals: 802.11ac and legacy 802.11 a/g/n/b; RF and Microwave pulse modulated power measurements: RADAR, MRI, Particle Accelerators; General purpose scalar measurements such as gain and return loss using modulated and pulsed signals as well as CW; and Monitoring, Recording, ALC loops, transient phenomena.
-
product
Extreme Low Power Detector Laser Power Meters
11XLP12
11XLP12 extreme low power detector is best suitable for low power im both the µW and mW regimes with very low thermal drift. Featuring broadband flat spectral response, minimal thermal drift and a noise equivalent power as low as 1 µW the 11XLP12 is ideally suited for measuring any pulsed or CW low power laser.
-
product
High-Power Digital Wattmeters
The Coaxial Dynamics High-Power Digital Wattmeters are designed for the accurate measurement of complex RF Waveforms such as CDMA (Code Division Multiple Access), DAB (Digital Audio Broadcast), DTV (Digital TV) and HDTV (High Definition TV), as well as CW, AM and FM.
-
product
Double Ridged Waveguide Horn
QRH18
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
product
Camera Based Beam Propagation Analyzer: M2
BeamSquared
The BeamSquared® system is a compact and fully automated tool for measuring the propagation characteristics of CW and pulsed laser systems from the UV to NIR to Telecom wavelengths. Users can also measure wavelengths above 1.8 microns, including CO2 and terahertz in manual mode (a bench set-up; without the automated optical train) with a Pyrocam IV or IIIHR. Our longer optical train and patented Ultracal™ Calibration makes BeamSquared the most accurate product on the market and is ISO 11146 compliant. Its operational robustness and reliability ensures continuous use applications in industry, science, research and development.
-
product
Fixed Wavelength CW Laser Source (DFB)
Laser 1200 Series
The Laser 1200 Series is a highly customizable fixed-wavelength Continuous Wave (CW) laser source available in a wide range of wavelengths and powers.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
product
SGMA RF Source
SGS100A
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
product
Digital Wattchman Monitor/Alarm Systems
Model 91091
The Coaxial Dynamics 'Digital Wattchman' Rack Mounted Station Monitor/Alarm is similar in function and appearance to our 81090 Series except it is designed for the accurate measurement of complex RF Waveforms such as CDMA (Code Division Multiple Access), DAB (Digital Audio Broadcast), DTV (Digital TV) and HDTV (High Definition TV), as well as CW, AM and FM.
-
product
Narrow band & Linear SSPA
Exodus Advanced Communications
Exodus Narrowband CW and Linearized SSPA products feature LDMOS, GaN,GaAsFET discrete and Chip & Wire Hybrid technologies covering frequency ranges from 1MHz to 26.5GHz at power levels exceeding 1KW for Modules and 10KW for Systems
-
product
PXIe Frequency Reference: 10 MHz And 100 MHz
M9300A
The M9300A PXIe frequency reference is a PXIe-compatible, compact, modular instrument that can be used with the Keysight M9301A synthesizer, M9310A source output, and M9311A modulator to create the world’s fastest vector signal generator, the M9381A. Create a CW source, the M9380A, by combining the M9300A with the M9301A and M9310A or use it as the 10-MHz or 100-MHz reference with other PXI solutions. Control the instrument through a soft front panel and programmatic interfaces tuned to your application development environment of choice.
-
-
product
Power Sensors
Measure CW power from 10 MHz to 50 GHz. Modulated Average Power Measurement. Peak Power Measurement.
-
product
Laser
BDS-SM Series
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz /50 MHz / 80 MHz / CW (Switchable)*Free Beam or Fiber Output*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
product
Saluki S1131 RF Signal Generator (9kHz to 3GHz)
S1131 RF signal generator provides engineers with a “Smaller, lighter and easier” solution for 3GHz signal-generation applications. While it is an entry level instrument, the S1131 provides most commonly used functions an engineer needs such as CW signal generation, AM/FM/PM/Pulse modulation, digital modulation (ASK, FSK, PSK), Up-converting, LF output etc. S1131 is perfect suitable for education, RF component manufacture and maintenance.
-
product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
product
Visual Fault Locator
FFL-310-U
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
product
Light Source Series
*High output power*Stable and reliable*CW or MOD output*MOD frequency: 270Hz/1KHz/2KHz*SMT, lightweight*Power supply by battery
-
product
Rotating Friction Torque Tester
Motorized Rotating Friction Torque Tester tests the smoothness of rotation and components of small precision motors, such as, gearbox, bearings, oil seals, etc. The motorized tester turns at a set rotational speed based upon the model. See the specifications table for more details. The tester can be used to measure torque in CW and CCW directions.
-
product
Visual Fault Locator
HW-205
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
product
Saluki S8723X Series USB CW Power Sensor (9kHz - 40GHz)
S8723X series is a diode detector USB power sensor based on a USB 2.0 full-speed/high-speed adaptive interface. It has a wide frequency range and large power dynamic range. It can be connected to a computer or other electronic measuring instruments, easy to set up a power test system, particularly useful for field and other low-cost production line testing and power testing.
-
product
Hi-Q Laser RIN Analyzer
OE4001
The OEwaves’ HI-Q® OE4001 Optical Test Measurement System (TMS) offers a fully automated measurement of ultra-low RIN (Relative Intensity Noise) CW laser sources.
-
product
Active Peak Reading Wattmeter
HF/6
Active peak reading wattmeter with simultaneously variable hold time on both the forward and reflected meter movements. This variable delay can be adjusted for quick action for high speed CW, or for longer periods more appropriate for the display of SSB and AM voice peaks. The peak detectors sport a new fast attack design capable of capturing quick pulses such as a single dit. Beautiful industrial design with tri color meter scale and brilliant LED illumination make the DWM series wattmeter a beautiful addition to any station.
-
product
NanoModeScan M² Measuring System
This scanning slit M² measurement system accurately analyzes lasers with wavelengths from UV to Far Infrared with its silicon, germanium, or pyroelectric head. It features a compact portable design, immediate results, ISO compliant measurements, and operates in CW or kHz Pulsed modes which makes it ideal for comprehensive analysis of lasers of most wavelengths.
-
product
Torque Gauges
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
product
Optical Light Source
TM102N
TM102N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at 1625nm, 1550nm, 1490nm, 1310nm, 1300nm, 850nm、650nm, single wavelength, dual-wavelength or tri -wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
product
Coupled Cavity TWTs
Communications & Power Industries
• Frequencies from 2.7 to 37.5 GHz• Peak levels: 500 W to 180 kW• Cooling type: air, liquid, conduction• Depressed or grounded collectors• CW (Continuous Wave) and Pulsed
-
product
IMPATT Noise Generator CW & Pulse At W-band, 94 GHz :
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
