Filter Results By:
Products
Applications
Manufacturers
RF Probes
Coaxial Probes are said to offer repeatable performance up to 3 GHz in custom or standard configurations.
See Also: Test Probes
- Pickering Interfaces Inc.
product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-874-102
The 40-874-102 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-874 has been minimized by careful attention to the mechanical and electrical design.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
product
Semi-Rigid Test Probes Up to 6 GHz
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
product
Broadband Isotropic Field Strength Probes
PI-01, PI-01E, PI-03, PI-05
Modern design probes meeting the requirements of most EMC and RF safety standards for RF safety, industrial, military and radar communication applications: 0.2-1000 V/m, 10 KHz-40 GHz.
-
product
Deep Access RF Probes
GigaTest Microwave Probes are perfect for device characterization and modeling. GigaTest Probes have a high tolerance allowing them to land repeatedly and take high-quality data.
-
product
Probe Head
cViper
cViper™ is an ultra-fine pitch probe head for RF and high speed digital WLCSP. cViper is ideal for lab and large volume production test for precision analog, RF, sensors and mobility devices. Low loop inductance and high bandwidth up to 27 GHz, cViper offers low and stable contact resistance for singulated devices or wafer-level test. A variety of contact materials to optimize performance are available with device pitch down to 100 µm.
-
product
RF Power Generators
MKS RF Power Generators provide reliable solid state power for thin films processing equipment. They are vital components of semiconductor fabrication systems, which produce the integrated circuits (ICs) or chips required by modern computers and electronic equipment. MKS RF Generators, combined with our Impedance Matching Network and our V/I Probe form a complete RF Delivery System.
-
product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
product
Test Contactor/WLCSP Probe Head
ACE
ACE™ test sockets offer optimal RF performance for fine pitch FBGA, QFN and wafer-level packages for Power Amplifiers, RF switches and mobile communications. Supporting pitches down to 0.4 mm, ACE features an innovative design that provides superior performance, improved yields and power efficiency.ACE probe heads deliver exceptional electrical performance, both DC and RF. Manufactured from HyperCore™ base material, a proprietary material of Cohu’s Everett Charles Technologies, ACE probes have the electrical properties of BeCu with the non-oxidizing properties of a precious metal. The short signal path, sharp tips, and large contact area between plungers provide high current conductance and reliable contact with less force.
-
product
TEM Cells
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
product
RF Near Field Probe Set DC to 9GHz
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
product
Active Differential Probe, 100 kHz to 7 GHz
U1818A
The Keysight U1818A 100 kHz to 7 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818A allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
product
Snap-on RF Current Monitoring Probe
TBCP2-250
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
product
RF Volt Meters
The latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range.
-
product
RF Helmholtz Coil
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
product
Compact Monitoring Probe
ISDB-T/Tb
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
MPI Automated Probe Systems
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
product
RF Coaxial Probes & Probe Positioner
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
product
Mixed Domain Oscilloscope
3 Series MDO
With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the 3 Series MDO sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the 3 Series has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.
-
product
Fiber optic thermometer systems
TS Series
Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:
-
product
Test Contactor/Probe Head
xWave
Highest performance and most robust RF broadband production solution for package, wafer, or Over-the-Air (OTA) test for 100 GHz.The xWave™ test contactor / probe head utilizes patented hybrid contacting technology to optimize RF performance and provide robustness for production testing of the most challenging cmWave and mmWave devices. Inside the xWave test contactor / probe head are embedded patch antennas and coplanar waveguides for both wireless and wired communication.
-
product
Calibration
RF Test Equipment
We calibrate following types of RF test equipment:EMF test systems (frequency selective)EMF test systems (broadband)Field strength transfer standards (e.g. RefRad)Line Impedance Stabilisation Network (LISN)Cable, attenuator, couplerAntennaField Probe
-
product
MPI Fully Automatic Probe Systems
MPI Advanced Semiconductor Test
Addressing the RF and High Power communication devices and discrete passive components production test market requirements, MPI introduced the TS2500 200 mm fully automatic probe system series. The system is based on industry leading production equipment from the Photonics Automation Division and incorporates decades of experience in RF and High Power measurement techniques from the MPI’s Advanced Semiconductor Test (AST) Division in combination with other AST products such as RF Probes, related calibration technology, and High Power accessories.
-
product
Probe Cards
U-Probe for Multi-die Test of Memory IC. Vertical-Probe Needle Type Probe card suitable for multi-die test of devices with peripheral pads. ertical-Probe Spring Type. Probe card suitable for area array pad test. 64DUTs Multi-Die. Probe Card for RF devices. Fine Pitch.
-
product
RF Capacitance Level Switches
ABB's RF Capacitance level switches feature one-step external calibration, immunity to material build-up, and a wide selection of probes for even the most challenging applications from low dielectric bulk solids to sticky slurries.
-
product
Near Field Probes 30 MHz - 6 GHz
XF Family
The XF family consists of 4 passive magnetic field probes and 3 passive E field probes designed for measuring magnetic and E-fields in ranges from 30 MHz to 6 GHz during the development phase. Due to their integrated impendance matching the probes are less sensitive in the lower frequency range than the RF type probes.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
WLCSP Probe Heads
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
product
6TL36 Plus In-line Test Handler w/Bypass
EA923
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
product
Enhanced Probe Station
EB Series
Comprehensive prober for DC and RF. The EB series contains features to step-up your usability to acquire the accurate data you need from your devices. It has a built in probe card slot.
