Filter Results By:
Products
Applications
Manufacturers
-
product
Ultrasonic Level Measurement
VeriGAP
Ultrasonic technology is a great choice for high or low-level liquid level measurement requirements in a wide variety of liquids. These ultrasonic sensors require no calibration and are not affected by changes in electrical properties of the material being measured.
-
product
Subsea Oil-In-Water Analyzer
The Mirmorax Oil-in-Water analyzer is based on an ultrasonic measurement technique in which individual acoustic echoes are characterized using advanced signal processing.
-
product
Ultrasonic Exhaust Flow Meter for Real-time Measurement of Vehicle/Engine Exhaust Flow
EXFM-ONE
EXFM-ONE employs an ultrasonic method for measuring exhaust gas flow rates directly from a vehicle or engine. The unit can be used for various applications such as real time mass measurement of raw exhaust gas combined with MEXA-ONE (Motor Exhaust Gas Analyzer), or for Particulate Matter/emission measurement combined with partial flow dilution system such as MDLT (Partial Flow Dilution Tunnel) or BMD (Bag Mini Diluter). Fuel consumption evaluation is also available when EXFM-ONE is paired with an optional air-to-fuel ratio (AFR) analyzer.
-
product
Digital Ultrasonic Inspection, Information, storage, and retrieval system
ULTRAPROBE® 3000
he Ultraprobe 3000 is a digital ultrasonic inspection, information, storage, and retrieval system that comfortably fits in the palm of your hand.
-
product
Ultrasonic Leak Detector
ULD-420
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
product
Stud Finders & Breaker Locators
Ultrasonic Distance Meter Laser Pointer measures from 2 feet up to 50 feetEasy-to-read LCD displayBuilt-in calculator for measuring areas and volumesAdds linear measurements, area and volumeMemory functionChoose from meter or foot unitsStud finder detects wood up to 3/4” with audio indicator & LCD displayAuto calibration stud detection
-
product
High Speed High Voltage Amplifier
WMA-320
The WMA-320 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-320 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications.
-
product
3-Axis Ultrasonic Anemometer
HD2003
HD2003 is a 3-axis static anemometer for measuring wind speed and direction, U-V-W cartesian components of speed, wind gust, sound speed, sonic temperature, air temperature, relative humidity and barometric pressure.
-
product
Double Sheet / Splice Inspection
Leuze electronic GmbH + Co. KG
Double-sheet control sensors enable the reliable differentiation between one or more layers of very thin objects made of different materials. This allows, for example, single-layer paper sheets to be reliably pulled in or individual electrodes to be stacked for the production of a battery cell. Different operating principles, based on ultrasonics and capacitive sensors, cover the range of materials for different applications. Sensors for splice inspection detect desired and random splices in paper webs independent of the surface color and material properties.
-
product
Ultrasonic Sensors
People Detection, Remote Bin Measurement, Automated Store Displays, Water Level Measurement, Parking Sensor
-
product
IP65/IP68 PAUT & Advanced TFM Solution
EXPLORER
The Explorer line offers the most advanced, compact, rugged ultrasonic device on the market. With a wide range of possibilities, you will find the Explorer adapted to your needs.
-
product
Ultrasonic Flow Meters
Dalian Taijia Technology Co.,Ltd
RS485 .4-20mA and OCT output● 4-20mA and PT100 platinum resistance input● 2×20 English letters LCD display● 4 key tactile-feedback membrane keypad● IP57● Operate with clamp on, insertion and flow-cell transducer● Pipe diameters from 15mm to 6000mm
-
product
CORROSION GAUGE
MX-1
The MX-1 will hold a single velocity, making it the perfect choice applications where only one material is being tested day after day. With the preset velocity in the gauge, you simply turn it on and go to work. The tool's backlit display is easy to read, even in dim light conditions, and the unit operates for up to 200 hours on a single set of AA batteries. The MX-1 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
-
product
Oil-in-Water Analyzer
LR2500
The Mirmorax Oil-in-Water analyzer is based on an ultrasonic measurement technique in which individual acoustic echoes are characterized using advanced signal processing.
-
product
Ultrasonic Testing
Pundit 250 Array
The Pundit 250 Array brings a quantum leap in the ultrasonic pulse echo testing. A number of unique innovations make the Ultrasonic multi-channel instrument the best and fastest solution for thickness measurements, detecting defects and localizing objects which cannot be easily detected by any other technology. This includes the assessment of thick concrete elements such as tunnel linings as well as pipes and tendon ducts beyond the rebar layer.
-
product
Ultrasonic Leak Detector
VPE
The Patented Superior AccuTrak VPE represents state-of-the-art technology for pinpointing leaks is air conditioning and refrigeration systems. AccuTrak is extremely sensitive to the ultrasonic sound of a turbulent gas leak. Using a technology called "heterodyning" it translates the sound to a lower frequency which your ear can interpret. AccuTrak maintains the original sound characteristics making it possible to distinguish leaks from other competing background sounds. AccuTrak is so sensitive you can actually hear the blink of an eye, yet most background noise will not interfere with detection accuracy.
-
product
Levitator
The ultrasonic levitator is ideally suited for a large number of material science experiments in which small samples or sample quantities have to be positioned precisely. Measurements can be conducted – as they are performed in a touchless manner – without interference from a contact surface.
-
product
12 Bit Waveform Digitizer Board
ATS9352
With data throughput as fast as 1.6 GB/s (1600 MB/s), ATS9352 is an ideal solution for many applications, including OCT, radar, ultrasonics, spectrometry and RF signal recording.
-
product
Ultrasonic Flaw Detector
MFD660C
MFD660C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed premium product, has a lot of advantages like unique design, sophisticated manufacturing, convenient operation, powerful function. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module， it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways in one body, customers with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
product
Ultrasonic Portable Hardness Tester
MET-U1A/MET-U1A50/MET-U1A100/MET-U1A110
The PHASE II ultrasonic portable hardness testers are capable of measuring the surface hardness of a broad variety of metals on flat, round, thin or large surfaces. Unlike the standard Dynamic hardness testers, these "state-of-the-art" portable hardness testers incorporate "Ultrasonic UCI" technology, which enables the hardness testing of very thin and small workpieces, which otherwise could not be tested accurately using a portable device.
-
product
Ultrasonic Testing
Xiamen IDEA Electronic Technology Co., Ltd.
Is a family of non-destructive testing techniques based on the propagation of ultrasonic waves in the object or material tested.
-
product
Ultrasonic Angle Beam Probes For Weld Seam Testing
SONOSCAN W
The ergonomic angle beam probes for Non-destructive Testing (NDT) from the SONOSCAN series inspect metals for cracks and inclusions. In the metal industry they are mainly used for weld seam testing. Our SONOSCAN probes are powerful, robust ultrasonic transducers which can be connected to all standard ultrasonic testing gauges.
-
product
PING))) Ultrasonic Sensor + Protector Stand
910-28015B
The PING))) Ultrasonic Distance Sensor is perfect for any number of applications that require you to perform measurements between moving or stationary objects. The sensor measures distance using sonar; an ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the echo return. Output from the PING))) sensor is a variable-width pulse that corresponds to the distance to the target.The protector stand was designed to help fortify the PING))) sensor against collision damage, and to provide a more stylish appearance in doing so. The stand is cut from high-grade aluminum and can be attached to your projects easily.
-
product
Leaky Insulator Detector
LIDOR
The Leaky Insulator Detector (LIDOR) is two-piece hand held non-destructive inspection system which utilizes AC/DC Current sensor and Ultrasonic technology for predictive maintenance. The Leaky Insulator Detector (LIDOR) has a Flexible clamp sensor and Ultrasound Receiver.
-
product
Wafer Inspection System
AutoWafer Pro™
AutoWafer pro is our most advanced ultrasonic equipment for detecting defects in bonded wafers in a production environment, providing fast, high-resolution scanning of 200mm and 300mm bonded wafers.
-
product
Ultrasonic Transducers
Low frequency transducers for ultrasonic testing of concrete and other course grained materials. Shear Wave transducers (pictured above) are used in combination with compressional wave transducers to calculate Poisson's Ratio. The line of general-purpose compressional wave transducers feature robust PZT elements in stainless steel.
-
product
Ultrasonic Hatch Cover Tester
ABS type approved and accepted by P&I clubs, this ultrasonic hatch leak detector is able to perform a quick and effective weathertightness test on hatch covers of dry cargo vessels and gives the exact location and the extent of leakage.
-
product
Ultrasonic NDT Transducers
United Western Technologies Corp
The Quick Change Transducer (QCT) series of transducers that makes changing wedge angle and transducer frequency rapid and easy, saving both time and money. The QCT connects straight into the wedges allowing for many combinations all within one kit. All QC Transducers are fitted with top mounted microdot connectors allowing for seamless transition from one transducer to the next. The stainless steel transducer housing will resist even the harshest working conditions. The emphasis of the QCT is general purpose with a balance of power and resolution, a High resolution version is available upon request.The Quick Change Wedge (QCW) is simple to setup and operate, utilizing incorporated noise dampening material on the wedge. Offered in steel, aluminum and titanium refracted angle. Custom contours, radii and wear pins available upon request.The QCT and QCW series are extremely versatile and can be used in many different applications and in a wide variety of industries and environments.
-
product
CORROSION GAUGE
MX-2
The MX-2 is ideal for the person that tests a few different materials regularly. The MX-2 contains 8 velocities of common materials and two velocities that the user can set using a simple sofware program. The tool's backlit display is easy to read, even in dim light, and the unit operates for up to 200 hours on a single set of batteries. The MX-2 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
