Filter Results By:
Products
Applications
Manufacturers
Couplers
enable a signal to be used in another circuit.
- LBA Group, Inc
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Signal Conditioning
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
product
Avionics Data Bus Tester
Distributed CORVUS
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
product
Inductive Coupler
CLAMPMITTER™
The CLAMPMITTER™ is a unique tool for inductive coupling. This self-contained inductive transmitter increases productivity, promotes safety and simplifies locates by condensing the transmitter and inductive coupler into one cordless package. Whether climbing down a manhole or accessing a utility box, the Clampmitter is an easy alternative to suiting up with a full transmitter and wired coupler.
-
product
Couplers
Macom Technology Solutions Holdings Inc.
MACOM’s couplers are used extensively in a wide range of aerospace and defense, wireless, and wireline communications applications. Our directional and hybrid couplers are offered in a variety of connectorized and surface mount packages with a broad range of coupling values ranging from 6 to 30 dB. Operating at frequencies from 2 MHz up to 18 GHz our couplers are ideal for real-estate constrained customers who need a high performing device for easy assembly.
-
product
PD Coupler
Techimp Capacitive PD Couplers offer both the PD and sync signals references, allowing a thorough investigation of the signal originating inside the asset they are connected to.Techimp Couplers are individually tested according to the following international standards: IEC60358; IEC60694; IEC60270.
-
-
product
Linear IC Tester
570A
The Model 570A Analog IC Tester's built-in test library includes all common Analog ICs including op-amps, comparators, voltage regulators, voltage references, analog switches & multiplexes, opto-isolators & couplers, and audio ICs.
-
product
Directional Couplers
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
product
ITSM Synchro
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
product
Directional Couplers
Virginia Diodes offers a broad range of millimeter-wave directional couplers for various applications. VDI directional couplers offer low insertion loss, coupling flatness and high directivity. Custom directional couplers may be available upon request. Contact VDI for more information.
-
product
RF Directional Coupler
ZDC9-20C1-40G-1661
Frequency 1000~40000MHz, Coupling 20dB, 20W, Connector 2.92 Female
-
product
Three-Dimensional Electromagnetic Simulation Package
QuickWave-3D
QuickWave 3D (QW-3D), is a universal user-friendly three-dimensional electromagnetic simulation package (winner of the European Information Technology Prize in 1998) based on the conformal FDTD method and supplemented with a range of unique models for curved boundaries, media interfaces, modal excitation, and parameter extraction. Complete 3D electromagnetic simulation offer a set of various results from wide area of applications. A lot of processing/postprocessings present a complete offer of comprehensive solutions from microwave components (filters, couplers, resonators, etc.) through antennas, TDR applications, optimisation and parameters sweep to simulation of microwave heating process (with Basic Heating Module) with temperature dependent media, static, rotated or moved heated object(s), and heat transfer.
-
product
3 DB 180 Degree Hybrid Couplers
KRYTAR's 180 Degree Hybrid Couplers offer wide frequency coverage in single, compact packages which provide low insertion loss, high directivity and tight coupling. These hybrid couplers offer simple solutions in many applications within those frequency bands including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted situations the compact size of these KRYTAR couplers are ideal. These couplers can be also be manufactured to meet military specifications.
-
product
3dB 90 / 180deg Hybrid Coupler
Panda Microwave offer Covering up to 60GHz 3dB Hybrid Coupler, average power 1 to 50 Watts, available in Narrowband, Ultra Broadband, IP65, IP67 and Vacuum types. Including 90deg Hybrid Coupler and 180deg Hybrid Coupler. Our products are widely used in military and wireless infrastructure applications. We offer wide frequency coverage in single compact packages. The feature low insertion loss, high directivity and tight coupling.
-
product
Coaxial Directional Coupler, 1 GHz to 20 GHz
87300B
The Keysight 87300B is a compact, broadband directional sampling coupler designed for signal monitoring or, when combined with a coaxial detector, signal leveling. It is supplied with SMA female connectors.
-
product
Coaxial Directional Coupler, 2 GHz to 18 GHz
773D
The Keysight 773D is a high-performance directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler is ideal for leveling broadband sources when used with a Keysight 8474B detector. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
product
RF Front-end
The RF integrated passive device (RF IPD) uses a high-resistivity substrate to integrate quality factor components such as capacitors and indictors. Many functions like impedance matching networks, harmonic filters, couplers, baluns, and power combiners/splitters can be designed using IPD technology. ST's IPDs are manufactured using thick film and HiRes Si or glass wafer manufacturing technology and photolithography processing.
-
product
Directional Coupler
DCZ-XXE/Y
The DCZ-XXE/Y directional couplers are used for extracting or introducing RF power flow in a transmission line withoutdistortion of signal characteristics. The directional couplers are available in 3, 6, 10, 15, 20 dB coupling values and30 - 35 dB minimum directivities*. 4-ports directional couplers are available in bi-directional (BDC4-XXE/Y) and dual-directional(DDC4-XXE/Y) configurations.
-
product
Fuel Injection Pressure Tester with 2 Gages & Quick Couplers in Storage Case
53980
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
product
RF Microwave Components
Specialized in passive RF microwave components, Radiall develops and manufactures a wide range of coaxial microwave components including terminations, attenuators, couplers, power dividers, filters and other specialized components. Our range covers a wide frequency spectrum from DC to 50 GHz, as well as low to high power, designed specifically for military, instrumentation, telecom and aerospace applications.
-
product
Wireless Measurement System for ETSI & FCC Devices for ISM Bands
TS8997
The R&S®OSP-B157W8 PLUS 7.5 GHz module with up to eight channels is the core of the system and uses a printed RF switch board in solid-state relay (SSR) architecture. It allows flexible operation of the connected DUT (up to eight ports) for power measurements, signal conditioning via the integrated attenuators, couplers and combiners, RF switching to the measuring instruments in combination with the R&S®OSP-B157WX up to 40 GHz and is controlled by R&S®WMS32 software.
-
product
Integrated Microwave Assemblies
Skylink offers high quality Integrated Microwave Assemblies and multi-function modules to meet customer requirements. IMAs integrate microwave components such as attenuators, switches, oscillators, amplifiers, filters, couplers and mixers, with the associated electronic circuitry, into one overall assembly.Skylink's integrated microwave assemblies are designed for both commercial and military applications in the frequency range from 100MHz to 50GHz.
-
product
Diesel Compression Tester
34700
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
product
Pump Combiners
Pump combiners, also called pump couplers, are special application fiberoptic couplers used for sending pump and signal light into an amplifier or laser fiber. Because of these applications, pump combiners are specially designed for high-power use.
-
product
Couplers (Quadrature, 180, Directional)
PMI offers the highest quality quadrature couplers for commercial and military applications in the frequency range of a few MHz to 40 GHz. If you do not see exactly what you need, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
product
Flexible Magnetic Coupler
FMC
The FMC (Flexible Magnetic Coupler) is a partial discharge sensor whose working principle is based on a direct magnetic coupling with the cable conductor and shield.It picks up a magnetic signal given by PD activity. His compact and robust design makes the FMC the optimal sensor for direct installation on cables and accessories such as joints and termination.This sensor has a sensitive side which has to face to the object under test, while the other side (shielded) reject the noise from the environment.
-
product
16 Channel WDM Mux/DeMux
S-106
16CH WDM Mux/DeMux module of FOTS system offers a function of multiplexing or demultiplexing up to 16 channel of WDM signals. This module offers low insertion loss, low crosstalk, and high temperature stability. An internally built-in AWG module functions as 1 X N optical Multi/Demultiplexers. The bi-directional feature of this module is ideal for wide range of applications. In combination with an optionally built-in circulator or C/L-band WDM coupler, this module can be applied to the WDM-PON test. User can easily make his or her test set-ups for FTTX-PON systems, especially for WDM-PON test, by combining this module with other FOTS modules such as SLED Driver, SOA Driver, C+L-FOTS modules such as SLED Driver, SOA Driver, C+L-band ASE source, Wavelingth meter, Transceiver Driver and so on.
-
product
PHOTO COUPLER TESTER
May be linked to machine handler for automatic test on production line.Test items include：VF、IR、Vceo、Iceo、Vsat、CTR
-
product
Lange Couplers
The Lange Coupler is a four-port interdigitated structure originally developed by Dr. Julius Lange in 1969. They are a common RF/microwave circuit. The coupling is derived from closely spaced transmission lines, such as microstrip lines. With the introduction of Ion Beam Milling, SemiGen’s ability to consistently produce Lange Couplers with lines and spaces as small as 10 microns and controlled to tolerances of +/- 1 micron is a direct result of our anisotropic ion beam etching process.
-
product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
