Filter Results By:
Products
Applications
Manufacturers
-
product
Millimeter Wave Continuously Variable Waveguide Attenuators
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
product
Waveguides
Waveguides from Fairview Microwave consist of coaxial adapters, bandpass filters, bends, flexible waveguide cables, waveguide gain horns, sections and terminations. Fairview waveguides are available in standard sizes from WR-430 through WR-15 depending on type of waveguide product, which encompasses frequencies from 1.7 GHz to 75 GHz.
-
product
Waveguides
CAES offers a full range of rectangular (WR-22 to WR430) and double-ridge (WRD-180 to WR430) waveguides covering frequency bands from a few hundred MHz to 100 GHz.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Ferrites and Waveguides
Wide range of Ferrite Devices Waveguide products for a variety of commercial, defence and space applications. The breadth of products includes devices operating from 1.0 to 52.0 GHz and includes isolators and circulators, combiners, transitions and terminations. Power combiners & dividers, Iso-adapters, WG loads, Isolators & circulators are offered in drop in, connectorized and micro-strip versions.
-
-
-
product
Millimeter Wave Spectrum Analyzer
Insight Product Co. offers the spectrum analyzer for frequency measurements of millimeter wave generators of continuous or pulsed signals. The spectrum analyzer can be ordered to cover a complete millimeter wave frequency band: 35-53 GHz; 53-78 GHz; 78-118 GHz; or 118-178 GHz and offer exceptional spectral resolution of 1-5 kHz.
-
-
product
Manual Attenuator (Waveguide)
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
-
product
WR-8 Waveguide Straight
WAG-08-SXX
Precision mmw F-Band, WR-08, Straight waveguides are built with high precision and then gold plated for high corrosion resistance. They have very low loss and great VSWR. Manufactured to rigid specifications, these transmission line components provide minimum detrimental effects on the overall system VSWR.XX = length in inchesFeatures of WR-08, Waveguide Straights• 90 GHz to 140 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-8 Waveguide Straight
-
-
product
Custom Waveguides
Custome waveguides for commercial, industrial, government and research & development industries. Consult with our engineering staff on your millimeter wave needs. View more Custom Waveguides
-
product
Waveguide Twists
Waveguide twists and bent types of waveguides are used extensively in electromagnetic devices. Twist waveguides are used to change the polarity of the fields. Waveguide twist VSWR is as low. Both 45° and 90° waveguide twists are available. The 45° versions being available in both right hand and left hand twist configurations.View more Twist Waveguides
-
product
Waveguide Power Sensor
V8486A
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
product
Waveguide Calibration Kits
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
product
Flexible Waveguide Assemblies
CAES provides an extensive portfolio flexible waveguides, waveguide assemblies, subassemblies of components, and assemblies in packages specifically designed to meet all of your requirements.
-
product
Waveguide Coupler
ZDC8-10W26.3-40G-2324
Waveguide Coupler, Frequency 26.3~40GHz, Coupling 10dB, Directivity 18dB Min, FBP320, 2.92mm Female Connector
-
product
Waveguide Receiver Protector
The continuous evolution of radar systems creates an ever more complex RF power environment in which sensitive receivers must operate and survive. Teledyne limiters deliver vital protection for a wide range of receivers, providing protection from L-Band through to Ka-Band (1 - 40GHz) and peak power levels up to 1MW with unparalleled low insertion loss levels.
-
product
Waveguide Power Sensor
W8486A
The W8486A waveguide power sensor measures average power over the frequency range 75 GHz to 110 GHz and power range -30 to +20 dBm.
-
product
Waveguide Accessories
Designed with our leading waveguide development expertise and application knowledge, CAES Waveguide accessories are offered in a variety of options, sizing and materials.
-
-
product
Double Ridged Waveguide Horn
QRH18
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
product
E Bend Waveguide
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
-
product
Waveguide Power Sensor
R8486D
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 26.5 GHz to 40 GHz Diode power sensing element
-
product
Radar Systems / Millimeter Wave Radar / Micro Wave Radar
KEYCOM develops various radars for versatile applications based on its knowledge and expertise on millimeter wave and microwave technologies. KEYCOM’s product line of radars includes Radar Test Systems (RTS) to evaluate distance accuracy or output, Radar Alignment Systems (RAS) to help you adjust the alignment of radars, and Radar Cross Section (RCS) measurement systems to measure RCS of such radar targets as aircraft, ships and automobiles.
-
product
Straight Waveguide Section
Straight sections are used to make connections between components in waveguide systems. Lengths and combinations are available on special order. VSWR is better than 1.1 over the full waveguide frequency band. Precision flanges on special order.
-
product
Waveguide Power Sensor
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
