Filter Results By:
Products
Applications
Manufacturers
Comb Generators
a reference signal source outputing multiple harmonics of the input signal.
See Also: Open Area Test Sites
- TEAM SOLUTIONS, INC.
-
product
Comb Generators
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
-
product
Low Phase Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Comb Generator
CG01
The main application of Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble shooting Open Area Test Sites(OATS).An OATS must be completely calibrated before it is put into service. reference signal source Noise Generators Signal Generators
-
product
Comb Generator
CG 50/500
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generators
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
product
Radiating Comb Generators
TBCG1
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
product
RefRad Comb Generators
RadRad is a battery-operated comb generator as well as a field source. It is a valuable tool for engineers ensuring the quality of radiated and conducted EMC and EMF measurements.
-
product
Reference Radiators / Comb Generators
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
product
Comb Generator
RefRad X
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
product
Phase Splitter Comb Generator
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
product
RF/MW Generators
Daihen Advanced Component, Inc.
Technical innovations such as miniaturization and three-dimensional applications are continuously happening in the field of semiconductors for making them more compact and packing more functionalities in them. “AVANCER” is a highly reliable (RF)power generator(s) brand equipped with various functions required by the next generation of semiconductor manufacturing processes, such as pulsed RF output and power saving. With proven technology and reliability, it contributes to the future of the ever evolving semiconductor industry.
-
-
product
Pattern Generators
PG311P Series
The MicroImage PG311 series of pattern generators are for applications to display custom designed patterns on screen. The PG311 units will overlay the pattern or patterns on top of the video signal provided to the input of the device. The PG311 can be factory programmed with one unique pattern.
-
product
Function Generators
PGP Electronics Private Limited
PGP Electronics Function Generators are a reliable source for different waveforms. Two units, function generator and frequency counter are integrated in to one unit. The built-in frequency counter can also be used to measure the external frequency.
-
product
Polydisperse Generators
This type of generator is typically capable of spraying aqueous solutions (e.g. salt), suspensions (e.g. PSL, nanoparticles), or oil or alike substances. They serve a variety of applications from laboratory research field tests of detectors, and filter testing.
-
product
Video Generators
Black Burst, Full Field and SMPTE Color Bars GeneratorsFull-featured Digital Pattern Generator DG-4Range of analog products from single output black burst (SG-2) up to six black burst plus SMPTE Bars (SG-7)Full Field ID generation available in SG-3, SG-7, BG-3 and BG-7 modelsNTSC (all models) or PAL (DG-4, SG-2, BG-2CB, BG-3/7, BG-4CB, and BG-5CB)
-
product
Punched Wet Film Combs (Aluminium)
112AL
The Elcometer 112AL, being punched from aluminium, is not as accurate as precision formed stainless steel wet film combs and has a shorter lifespan.
-
product
Wet Film Combs (Stainless Steel)
Elcometer 115
Four separate thickness ranges are available up to a maximum of 1,250μm or 50mils and are manufactured to an accuracy of ±5% of marked value or ±3µm (0.12mil), whichever is greater.
-
product
Signal Generators
SSG5000X Series
SIGLENT’S SSG5000X series of signal generators can generate analog and vector signals, and have a frequency range of 9 kHz to 4 GHz/6 GHz. They feature the industry-leading performance in phase noise, spectral purity, bandwidth, EVM, output power. The internal IQ modulation generator and waveform playback function make it easy to create even the most complex signal types. They also cover the most important RF band for digital wireless communications and include standard waveform files. The SIGLENT SSG5000X are powerful and cost effective sources that are ideal for R&D, education, and manufacturing.
-
-
product
Monodisperse Generators
Specific applications include calibrating particle counters, testing various filters, and studying size-dependent particle properties.
-
product
Function Generators
Advanced Energy's Trek function generator and amplifier systems can be used in a broad range of R&D and production applications. Features include our exclusive instrument control and interface for remote operation.
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
