Filter Results By:
Products
Applications
Manufacturers
- Taylor Dynamometer, Inc.
product
1100 HP Water Brake Chassis Dynamometer
TD-36
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
product
Tachometer Tester
Maschinenbau Haldenwang GmbH & Co. KG.
for motorcycles, for cars and vans up to 4000 kg and for cars and trucks up to 13000 kg axle load.
-
product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
product
Roller Brake Testers for Max. 5000 kg Axle Weight
The VLT roller brake testers perform very accurate, reliable and fast measurements. All roller brake testers comply with the highest standards and are of high quality. There is a perfect roller brake tester for every garage or workshop. VLT roller brake testers achieve the lowest cost of ownership because of their longevity. They are available for a wide range of vehicles; from motorcycles to cars and lorries.
-
product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
AWD Dynamometers
MD-AWD-500-AC/EC-100/250
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
product
Testing of Rear Axle Steering
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
product
Axle Load Simulators
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
product
Towing Dynamometer
RS-125K
RS-125K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-125K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-125K is designed to maintain 125,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds
-
-
product
High Speed Load Cell Test Interface
LCIC-4CH
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
product
1650 HP Water Brake Chassis Dynamometer
TD-24X3
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 35 mph (1,230 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rolls, 2 sets of 2 rear rolls to accommodate axle spreads from 48 to 66 in. (1,219 to 1,676 mm) tandem centers and 52 to 62 in. (1,321 to 1,575 mm) tridem centersPit Required Depth: 27 in. (686 mm)
-
product
Dynanometer Roller Set
FPS 2700 | VP 230048
Maschinenbau Haldenwang GmbH & Co. KG.
The FPS 2700 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. As a result of the increased tractive force of its eddy current brake, the FPS 2700 is additionally suitable for power measurements at constant speed and constant tractive force.
-
product
Towing Dynamometer
RS-90K
RS-90K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-90K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-90K is designed to maintain 90,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Axle And Joint Play Tester
Maschinenbau Haldenwang GmbH & Co. KG.
Axle And Joint Play Tester
-
product
Profiling Systems
ICK profiling systems measure, detect, classify, count, and check vehicles in 3D. They determine the number of axles on heavy goods trucks for vehicle classification and measure vehicle dimensions to rectify loading errors. The systems recognize overheated vehicles approaching tunnels and other entrances and activate diversions. They also monitor external train contours. If a limit value is exceeded, the system triggers an alarm. All this contributes to safety on roads and railroads.
-
product
4WD Roller Set
ASM-BF/2 | VP 230044
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/2 4WD roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-BF/2 4WD is built into the base.
-
product
Shock Absorber Tester
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
product
920 HP AC Chassis Dynamometer
TD-36-AC
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 39,400 lb (17,872 kg)Capacity: 920 hp at 40 mph (686 kW at 64 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in (1,219 to 1,880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
product
Towing Dynamometer
RS-200K
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Towing Dynamometer
RS-60K
RS-60K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-60K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-60K is designed to maintain 60,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Brake Test Systems
Giant 8000 Series
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
product
Structural Durability Solutions
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
product
Agriculture Solutions
The trend in agriculture: The drives of machines and commercial vehicles must be capable of transmitting increasingly high power within a limited space. Reproducible quality in series manufacture with the shortest possible production times are the key requirements in this industry.The hay makers and harvesters perform their task using straight bevel gears. Because the loads in these machines are comparatively small, a cost-effective manufacturing solution is crucial for the market success of straight bevel gears. It’s a different story as far as tractors are concerned: Spiral bevel gears are installed in the rear axles in this case – and the bevel gear set of a tractor’s rear-axle differential must transmit up to 400 kW. In tractors, cylindrical and planetary gears are also used in manual transmissions and counter shaft transmissions as well as planetary gear drives for transmitting power to the enormous drive wheels. These cylindrical and planetary gears must be efficient, quiet-running, and low-maintenance. With solutions from Klingelnberg, the entire portfolio can be produced on bevel-gear and cylindrical-gear machines.
-
product
Wheel Play Detectors
A play detector consists of two plate units on which the wheels of an axle are placed. The plates are moved horizontally in an oscillating fashion by hydraulic cylinders. This movement can be done in different directions. In this way an inspector in the inspection pit can easily check for play on the different components underneath the vehicle. To make it even easier, the remote control unit to start and stop the plate movement has a built-in lamp.
-
product
622 HP Eddy Current Chassis Dynamometer
CM-51-EC
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 8,340 lb (3,783 kg)Capacity: 622 hp at 45 mph (464 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long4 front fixed rolls, 2 rear rolls fixed toaccommodate axle spreads from48 to 60 in. (1,219 to 1,524 mm)tandem centersPit Required Depth: 25 in. (635 mm)
-
product
Towing Dynamometer
RS-110K
RS-110K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-110K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-110K is designed to maintain 110,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Axle Damping Test
MSD 3000 | VP 215033
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test stand MSD 3000 is characterized by a quick and precise physical check of the axle damping. The frequency-controlled plate excitation by means of electric motors determines the maximum oscillation amplitude and then evaluates the axle damping according to the principle of Lehr's damping. The fully automatic test sequence including the determination of the axle and vehicle weight enables a time-saving and reliable assessment of the axle damping.
-
product
Vehicle Testing Technology
Maschinenbau Haldenwang GmbH & Co. KG.
Vehicle testing technology includes products for testing axle damping, wheel arches and axle and joint play. Diagnostic devices for eg the sound level or clamping force also make their contribution to the targeted assessment of the vehicle condition.
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
