Filter Results By:
Products
Applications
Manufacturers
SPI
assures volume and area of paste application.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Firmware for High-speed HDLC Mode
OP-FW10G
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
-
product
Environment click
Environment click measures temperature, relative humidity, pressure and VOC (Volatile Organic compounds gases). The click carries the BME680 environmental sensor from Bosch. Environment click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI or I2C interface.
-
product
Gyroscope Module 3-Axis L3G4200D
27911
The Gyroscope Module 3-Axis L3G4200D provides raw angular rate and temperature data measurements that are accessed from the selectable digital I2C or SPI interface. The small package design and SIP interface accompanied by the mounting hole make the sensor easy to integrate into your projects. Designed to be used with a variety of microcontrollers, the module has a large operating voltage window.
-
product
SparkFun SAMD21 Development Board
Qwiic Micro
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
Wide Band Filters (multi-octave)
HF-ERF™ Series
The HF-ERF™ is an internally switched 3‑band, low cost, miniature, high performance tunable filter. The HF-ERF™ was designed to have the best insertion loss and Q in the smallest package possible, 2.0” x 2.78” x 0.6”. All HF-ERF™ filters are fully tested and aligned by Pole/Zero for convenience and ease of use. Both SPI and Parallel control interfaces are available in one filter. Modified variants are available upon request.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
Firmware for High-speed HDLC Mode
OP-FW10R
OP-FW10R is a firmware to expand the measurement speed for bit synchronous communication such as HDLC/SDLC/X.25, CC-Link and SPI communication up to 10Mbps. Processing major part of the measurement process by FPGA, it enables capturing of communication data with time stamp of micro-second unit.
-
product
Gas Flow Sensors
ESRF-ESF Sensor
ESRF-ESF is one of the few gas flow sensors featuring bidirectional gas flow sensing of up to ±300 ln/min with a total error band of < 1.25% RD. ESRF-ESF gas flow sensors provide calibrated and temperature compensated output on an SPI, I2C bus or analog output making them plug & play for direct interfacing to low voltage MCUs and systems. The user is provided with a multitude of interface and output options so that the right sensor configuration can be selected based on the specific requirements for each application.
-
product
Miniature Spectrometer
Ocean HDX
Ocean HDX is anchored by High Definition Optics for high throughput, low stray light and great thermal stability. Its X-Platform Electronics include powerful onboard processing and communications including Gigabit Ethernet, SPI and Wi-Fi. The Ocean HDX is compact, robust and ideal for integrated, industrial and research applications.
-
product
SparkFun TFT LCD Breakout
1.8" (128x160)
The SparkFun TFT LCD Breakout is a versatile, colorful, and easy way to experiment with graphics or create a user interface for your project. With a 4-wire SPI interface and microSD card holder, you can use this breakout to easily add visual display/interface capabilities to a project as well as providing all the storage you might need for multimedia files.
-
product
Unipolar D/A Converters
Analog Devices offers the broadest portfolio of low voltage single-supply d/a converters in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+® products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
product
Evaluation Board
emPower
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
product
Multibus Ethernet Card
MS 1750
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
product
Flash Programmers
Easy fixture integration thanks to the compact size: 142x17,6x70mm, Independent ISP channels supporting several communication protocols (JTAG, SPI, I2C, BDM, UART, 8 digital I/O lines for each channel, coupled with dedicated ground return lines.
-
product
AOI & SPI Test Systems
To keep the quality of your production at its best you need a good inspection of your boards. For efficient and detailed in-depth board inspection ensure you have SMT inspection equipment that meets your needs. Our AOI & SPI units will provide the quality you need for reliable inspection of soldering inspection.
-
product
SparkFun Qwiic Micro:bit Breakout (with Headers)
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
AOI & SPI Test Systems
Xceed AOI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The Xceed enables true 3D measurement and provides the most accurate and repeatable inspection results with the minimum false calls. It’s designed with Advanced Signal Processing which gives results in noise-less, clear, and accurate 3D images.
-
product
SOM Module
TEO820-ZU2CG
Sundance Multiprocessor Technology Ltd.
Xilinx Zynq UltraScale+ XCZU2CG-1SFVC784EZU2, 784 Pin Packages4 x 5 cm form factorRugged for shock and high vibration2 x 512 MByte 32-Bit width DDR4 SDRAM2 x 32 MByte (2 x 256 MBit) SPI Boot Flash dual parallel4 GByte eMMC Memory (up to 64 GByte)B2B Connectors: 2 x 100 Pin and 1 x 60 Pin
-
product
8-Sites ISP & I2C/SPI Interface
YAV90ISP
Industrial Programmers Interface up to 8 targetsRelay BarrierDemultiplexer module up to 32 devicesCommunication Interfaces I2C and SPI
-
product
MIPI I3C Sensor Controller
I3C
The main purpose of MIPI I3C is to standardize sensor communication, reduce the number of physical pins used in sensor system integration and support low-power, high-speed and other critical features supported by I2C and SPI.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
product
Dual Band Block Up-Converter
DBUC Series
*Connectorized Package *Wide Choice of Frequency Ranges *Dual Band *Integrated Filters *Gain Control *CAN, RS-232, I2C, or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
