McLAREN Applied Technologies
Technology is the lifeblood of the McLaren Group. It drives our motorsport and automotive success, which in turn creates an infrastructure geared to further innovation. As part of the Group, McLaren Applied Technologies is uniquely positioned to capitalise on progress made within the broader business.
- +44 (0)1483 261 400
- sales@mclaren.com
- McLaren Technology Centre
Chertsey Road
Woking, Surrey GU21 4YH
United Kingdom
-
product
Interface Units
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
product
Speed Sensors
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes.
-
product
Signal Conditioning
The output of an inductive (magnetic reluctance) speed sensor is an alternating voltage in which both the frequency and magnitude depend on target speed. The TTL Interface Adaptor converts this voltage into a TTL logic signal whose frequency corresponds to tooth passing frequency. The magnitude of the output signal from the interface is independent of the tooth passing speed.
-
product
Microwave Transmitter
LTX-310B
LTX-310B is a self-contained microwave transmitter for use with the LRX-310B receiver. The output is pulse modulated to identify one of 36 channels arranged in six groups of six. The group is set at the factory and you can select one of the six channels in that group from an external rotary switch.
-
product
Thermocouple
This sensor uses a K-type Chromel/Alumel thermocouple and is intended for use in high-temperature, high-vibration environments. Control units and data loggers support K-type thermocouples. The sensor is short and compact to minimise its susceptibility to vibration.
-
product
Sport Sensor Range
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes
-
product
Fluid Level Sensor
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
product
Data Loggers
The unit can acquire data from on-board interfaces at rates of up to 10 kilosamples per second, and from remote units via communications links. A high-performance on-board PowerPC microprocessor offering over 1000MIPS processing power hosts customer applications for real-time data analysis. Application code may be autocoded using our Graphical Development Environment (GDE) from Matlab/Simulink control modules. Data is logged to 2GB of on-board Flash memory and downloaded for analysis via a Gigabit Ethernet network connection.
-
product
Pressure Sensors
The output voltage of this sensor changes with absolute pressure. An internal amplifier creates a single-ended, amplified output in the 0 to 5 Volt range, so the sensor can be connected directly to most control units. The body and diaphragm are impervious to chemical attack by standard motorsport fluids.
-
product
Thermal Camera
The thermal camera allows real-time thermography with 100Hz frame rate via USB 2.0 interface. The camera is lightweight, compact and rugged (IP65). Measurement ranges of -20C to 100C, 0C to 250C, or 150C to 900C are selectable in software. Interchangeable lenses are available with 6x5, 23x17, 48x31 and 72x52 field of view.
-
product
CDI Ignition Coil
An on-plug coil for use with Capacitive Discharge Ignition (CDI). Design and manufacture is in-house, so we can make the coil to suit your specific application. The information given here is for a typical coil. Many of the parameters can be tailored to a particular installation.
-
product
Pressure Sensors
The output voltage changes with the absolute pressure applied to the pressure port. The gain, offset and thermal drift of the pressure sensor is digitally compensated to minimise errors and to create a single-ended, amplified output in the 0 to 5 Volt range.
-
product
Torque Systems
The Drive Plate Torque System uses a low power radio link to transfer digitised strain measurements from a rotating wheel hub to a stationary antenna mounted nearby. The signals are passed to a receiver where they are decoded and output as CAN bus messages and analogue outputs.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Electronic Control Units
Self-contained engine management system and data logger for race engines up to eight cylinders. The unit is complete with integrated ignition and injection drivers and so needs no external units to run an engine.
