JTAG Technologies Inc.
We are a solutions company specializing in PCB assembly testing, fault diagnosis and device programming. We develop innovative products built upon boundary-scan (IEEE Std 1149.x) standards and supply our software and hardware products and services world-wide.
- 877 FOR JTAG
+31 (0) 40 295 0870 - +31 (0) 40 246 8471
- info@jtag.com
- Boschdijk 50
Eindhoven, 5612 AN
Netherlands
-
product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
product
19" Rack Mount Chassis, Industrial JTAG-Powered PCB Tester-Programmer 'CombiSystem'
JT 57××/RMIC
The new-concept, industrial JTAG-powered PCB tester-programmer the JT 57xx/RMIc ‘CombiSystem’ comprises a sleek base-level 19″ rack-mount chassis assembly that can house up to four customer-specified modules chosen from various JTAG (IEEE 1149.x) controllers, digital IO and analog IO and other measurement modules.
-
product
CoreCommander
While many ICs are equipped with a JTAG (IEEE Std. 1149.1) boundary-scan register (BSR), a significant number of microprocessors and DSPs can be found with deficient or even non-existent BSRs. CoreCommander Micro uses the on-chip debug mode of processors to access ports and embedded peripheral controllers to promote ''kernel-centric'' testing. Similarly, in the case of today's Field Programmable Gate Arrays (FPGAs) test engineers can ''bridge'' from the JTAG interface to the resources of the gate array itself. Our CoreCommander FPGA product implements a translatorinterface that allows our JTAG hardware to control embedded IP cores via a variety of bus interfaces (e.g. Wishbone Avalon etc.).
-
product
DIOS (Digital I/O Scan Module)
JT 2122/MPV
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
product
JTAG Live Controller
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
product
JTAG Visualizer
JTAG Visualizer is an advanced graphical viewer and data management system for PCB schematics and layouts. Visualizer integrates seamlessly with the JTAG Technologies family of boundary-scan products, such as the ProVision application development platform, and accepts PCB data from a variety of CAD, CAM and EDA tools. In design Visualizer provides DfT (design for test) feedback to the user by enabling a graphical view of fault coverage on their design. In manufacture and test Visualizer can be used to highlight faulty nets (short circuits, opens, stuck-ats etc.) in both layout and schematics views.
-
product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
product
TAP Pods
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
I/O Modules
JTAG Technologies designers have been developing high-speed digital test equipment for well over 30 years. The current range of controllers ranges from the compact, stylish and reliable JT 3705/USB to the rugged, dependable DataBlaster family and variants that have been developed for industrial use. The latest addition, JT5705/USB adds analog measure and source capabilities to provide a true mixed-signal tester platform.
-
product
Training Board
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
product
Digital/Analog/Frequency Measurement Module
JT 2149/DAF
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
product
BSD (Test Diagnostics)
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
Children
-
Corelis, Inc.
Corelis is a pioneer in the rapid development of innovative IEEE-1149.x-compliant products and services in support of the JTAG/boundary-scan market. As a result of our ingenuity and contributions to the industry, a growing number of customers have been able to incorporate boundary-scan technology into their product development processes in order to gain a competitive edge in today’s marketplace.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
-
DFT - MG-Products BV
DFT, Designed for Testing. is part of MG-Products and is specialized in the delivery of functional Testfixture solutions from both MG-products and 6TL. DFT also stands for Design For Test, perhaps the most important step in the development process of your product. DFT ensures that your product can be contacted and tested efficiently and reliably.
